Samsung SCC-C6455N user manual Screw Fixing Hole Diagram

Page 11

2.Use the three “SCREWS” to fix the “FRAME SET” on a “CAMERA” installation position.

FRAME SET English SCREW

SCREW

ADAPTOR

SCREW <Fixing Hole Diagram>

3.Connect external cables to the “CONNECTORS(ALARM IN, POWER, RS-485, ALARM OUT)”and connect the “CONNECTOR” to the “ADAPTOR”.

Insert the cable into the “FRAME SET”, and close the “ADAPTOR”.

 

 

 

FRAME SET

 

POWER INPUT ALARM OUT

ADAPTOR

ALARM IN

RS-485

 

 

 

 

SNAP FIT

 

 

 

BNC JACK

 

 

 

INSULATION TUBE

M

Then, wrap the “BNC JACK” with the “INSULATION TUBE”, and use an insulation

tape to seal up the end of the “INSULATION TUBE” so that the “BNC JACK” does

not protrude outside of the “INSULATION TUBE” coating.

For more information about cable connection, refer to “Connecting the adaptor cable”. (page 19)

English _11

00885A-NA_SCC-C6455N-ENG.indb 11

2009-08-05 오후 2:43:

Image 11
Contents Smart Dome Camera Overview English  Overview FCC Statement Important safety instructions Contents What’s Included FeaturesFrame SET At a GlanceCamera Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Use SW606, SW605, and SW604 to specify the camera address Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationVideo terminal on the rear of monitor BNC Cable Connecting with Other deviceConnecting to a monitor To connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu  ITS ProfileNight VPS You can configure the general settings of the camera moduleCamera SET Camera IDBLC With Backlight set to IrisDNR With this, you can adjust the AGC level of aAGC MotionXDR ShutterSENS-UP FlickerlessAny excessively bright area in a night scene will be MASKed You can specify a recording mode according to the sceneDAY/NIGHT SET-AUTO SET are not available Auto Switch or Auto FocusWhite BAL  You can specify Mask 1 and 2 simultaneouslyDAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset SET. pages 24 ~ Select the preset numberSelect Position and adjust PAN You can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup ~ 511 for Preset Auto Play SetupSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Tilt range -6˚~186˚ Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Manual Pan Speed 0.01˚~ 180˚/secProduct Appearance 00885A-NASCC-C6455N-ENG.indb 2009-08-05 오후