Panasonic TH37PR11UK Maintenance, Setup, AC Power Supply Cord, If problems occur during use

Page 7

Safety Precautions / Maintenance

WARNING

Setup

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

Transport only in upright position!

Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, and 2 3/4” (7 cm) or more at the rear, and also keep the space between the bottom of the display and the floor surface. If using some other setting-up method, follow the manual of it.

AC Power Supply Cord

The Plasma Display is designed to operate on 110 - 127 V AC, 50/60 Hz.

Do not use any power supply cord other than that provided with this unit.

• Doing so may cause fire or electric shocks.

Securely insert the power cord plug as far as it will go.

If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

Maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

7

Image 7
Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits When using the Plasma Display Safety PrecautionsIf problems occur during use MaintenanceSetup AC Power Supply CordAccessories Supplied AccessoriesCheck that you have the Accessories and items shown AC cord fixing ConnectionsCable fixing band PC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorCommunication parameters Signal names for D-sub 9P connectorCommand Serial Terminals connectionConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet INPUT1 INPUT2 INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageBasic Controls On OFF Aspect Controls All Aspect modePanasonic Auto Multi PIP Advanced PIP Select the magnification required for the enlarged display Digital ZoomDisplay the operation guide PositionOn-Screen Menu Display Adjusting POS. /SIZE Cinema Picture AdjustmentsStandard DynamicAdvanced Settings Press to exit from adjust mode Sound AdjustmentSET UP Timer Present Time SetupPresent Time Setup Function selection Setup of Screensaver TimeStart setting Screensaver For preventing image retentionReduces screen image retention Side BAR AdjustOFF Dark MID Bright Reduces power consumption Addition sign Selected Input Customizing the Input labelsINPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 PC/COMPONENT/RGB/DVD/STBComponent / RGB in Select SET UP for Input SignalsYUV / RGB in Select For Component Signal menuWhen ON, this setting only affects Ntsc input signals 3D Y/C Filter For Ntsc AV imagesPulldown XGA ModeMode Function Color System / Panasonic AutoAdvanced NR Press to adjustRefresh Rate Noise ReductionSetting RGB sync signal Input signal displaySync Press to adjust the menu Press to exit from Options menu Options AdjustmentsOptions Adjustments Normalization Program Edit screen Weekly Command TimerPress Action button Program numberPress to set each item Press to select Time / CommandTime Set the time to execute a command program Shipping conditionPlasma Display panel TroubleshootingFull List of Aspect ModesRGB PC input signalsCommand list of Weekly Command Timer TH-37PR11UK/H TH-42PR11UK/H SpecificationsFor the U.S.A Panasonic Professional Flat Panel Display Limited WarrantyFor Canada Limited Warranty StatementPage Page Page Panasonic Canada Inc Customer’s RecordPanasonic Professional Display Company Executive Office