Philips SM30 manual Microphones, Programming next microphone

Page 43

 

2

 

 

SELECT PROGRAM :

 

MICROPHONES

1

 

 

2

 

 

 

SELECT ITEM :

 

MICROPHONE : X

3

MICROPHONE : X

 

PRIORITY : X

4

 

 

 

MICROPHONE : X

 

SIGNAL : XX

 

5

 

 

 

MICROPHONE : X

 

MESSAGE : X

6

 

 

 

MICROPHONE : X

 

000000

ZONE : 01

7

 

 

 

MICROPHONE : X

 

XX0000

REL : 03

Microphones

 

2.7Programming Control Relays

This display will be skipped if the Control Relay Module is not present in the system. The current setting of Control relays 1-6 is shown. Shifting the cursor to the right, further than the last position, will display the current setting of relays 7-12. Selecting a zone can be done with the ‘’ key. Deselecting a zone can be done with the ‘O’ key. Relay 1 (marked ‘X’) is reserved for the activation of internal system error indicators and cannot be programmed for any other function. Relay 2 (marked ‘X’) is reserved for the activation of Call Station error indicators and cannot be programmed for any other function. Relay 3 is dedicated to the ‘Delayed Power On’ function, but may be used for other functions if Power On Delay is not used. If it is used, the third position will be marked with an ‘X’ in the display.

Programming next microphone

When programming of the first microphone is completed, pressing ENTER returns to the next microphone number to be programmed.

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents SM30 Contents Control Centre IntroductionProgramming SM30 plug-in modules Signal generatorEmergency Power Supply +48 VDC Block diagramBlock diagram Typical Operation System OperationActivation of Control Relays Power on delay Volume Control Override RelaysAlarm interrupt Alarm Tones Signal descriptionTime signals Front panel controls ON/OFF Power Switch fig.4.1AProgramming Keys fig.4.1C Music Function Keys fig.4.1E Alpha-Numeric LCD Display fig.4.1DSM30 basic modules Power Supply ModuleLine Output Module General Setting UP the HardwareRemoving Module Blank Panels Opening the housingMounting the Modules Volt Emergency Power Supply Voltage SettingEarth Terminal ground General Rules Mounting in a 19 rackRemoving Feet Calculating Required Rack SpaceOne Channel System fig.5.5.2 Connecting amplifiersRack Mounting 1 Two channel system 2 One channel system Operating controls Numeric Keypad fig.6.1J Electret condenser microphoneBuilt-in Compressor Balanced Line Level output‘Press-To-Talk’ Key fig.6.1H Call StationUsing the Call Station Using the Keypad to make a Call Installation Loudspeaker Zone TemplateAdjustments LED Intensity PresetPage Connection of Call Stations Installation Mounting in the Control CentreAdjustments Volume Level Controls Call Station Input Module CSMBass Cut Facility Operation Remote Switching FunctionMicrophone Input Module MIM Line Input FacilityCIM Adjustments Gain Control PotentiometersConnection of Microphones Control Input ModuleDirect routing Wiring control inputsMicrophone Input Adjustments Output Volume ControlAutomatic Gain Control Headphone MonitoringRecording over an Existing Message Safety FeaturesNumerical order, commencing with message Recording a MessageMusic Source Inputs Remote Location RecordingMusic Input Module MUMDisplay music source status Programming Software routing to zonesZRM Zone Relay ModuleTerminations Multiple Amplifier Configurations Coupling Zone Relay ModulesCRM Control Relay ModuleProgramming Power-on delay Remote Volume Control OverridesInstallation Wiring Control RelaysProgramming Program step Selection User passwordSummary SM30 User Programming User Program User Programming ModeIntroduction GeneralCall Stations Key Pad Selection Signal number selectionMain menu selection Call Station number selectionKey Priority selection Key Signal number selectionFunction Key number selection Key programming selectionKey Music on/off Key Music volume upKey Music volume down Key Relay switching selectionMicrophone number selection MicrophonesCall Routing to Zones Programming next microphone MicrophonesPriority level selection input Control InputsControl input number selection Control inputProgramming Control Relays Control InputsGeneral SM30 System SpecificationMains Supply DL L Audio signal level diagramMusic Routing Return to ‘RUN’ modeError Messages Music RoutingPage Supplement Instructions for installation Contents Extended Call Station Programming Installer programming stepsselectionSetup Store hardware Installer modeSystem down Language selectionMusic Input Text Power-on DelayPOWER-ON Delay Delay timeAlternative text selection Select LanguageAlternative Music Input Text Input number selectionAltering selection Storing Hardware Selecting Amplifier ConfigurationStore Hardware Amplifier Configuration Configuration displayRemote Volume Control Music Volume Step/RepeatMode display Call Station selection Volume Control Routing Limits Call Override Relays StationOverride Relays Relay selectionCurrent zone display Routing settingRouting Limits Direct Routing14.2 Confirmation Clear Memory Control Alarm ModePower-on delay System down Clearing MemoryFlexible F-keys 17.3 Confirmation Extended Call StationExtended Call Station Programming Selection Call Station input numberMPL if IE R C ONF IG Xxxxxx R MA N Singl E AMP LIF IE RS MU SIC Z on ES SE T ROU TIN G VIA Inst AL LE R P Rogr AM EL ECT PR Ogram CT L AL AR M MOD E SEL ECT FUN Ction MIC ROP Hone Priority Page Page 3922 988 33415 20/97
Top Page Image Contents