Sharp PN-V600 Connection with the control kit optional, Connect the monitors in order

Page 14

Connecting Peripheral Equipment

■ Connection with RS-232 cable

If you connect the monitor in a daisy chain using RS-232 cable, using the monitor buttons on the primary (main unit), settings are copied to the secondary (expansion unit) and operation from the primary can perform operation for all monitors. Setting each ID No. in the monitor is required.

1.Connect the monitors in order.

The first monitor will be set as primary (main unit) and the second monitor and beyond will be secondaries (expansion units).

Connect the RS-232C output terminal of the first monitor (primary) and the RS-232C input terminal of the second monitor (secondary) together using RS-232 cable (straight). Connect in the same way to the third and subsequent monitors. Up to 25 monitors can be connected. (Depending on the length of the cable used and the surrounding environment.)

First monitor: primary Second monitor: secondary

RS-232C

RS-232C

RS-232C

output terminal

input terminal

output terminal

RS-232 straight cable (commercially available)

Third monitor: connects to secondary RS-232C input terminal

2. Set the ID No.

Perform operation with the rear side buttons on the primary monitor. If you set AUTO ASSIGN ID No., located in the menu of the monitor to ON, the ID No. will be automatically assigned in order from the primary. (See page 24.)

(If you attach PN-ZR01 the control kit (optional), you can perform operation of the monitors with the remote control unit.)

■ Connection with the control kit (optional)

If performing operation of the monitor with the remote control unit, the PN-ZR01 control kit (optional) is required.

•Can perform operation of an arbitrary monitor or all monitors with the remote control unit of the first monitor.

•Can perform operation of up to 25 monitors.

•Connect the monitors together in a daisy chain with RS-232

cable.

Attach the remote control sensor box as shown in the following illustration.

*When attached to the left side, because the top and bottom for the remote control sensor box will be reversed

(the connection cable will be on top), the right side is recommended.

Caution

•When attaching the remote control sensor box, turn the main power switch OFF.

•Except for the remote control sensor box connection cable, do not insert any other cable into the control kit terminal. Also, do not connect any connection cables that have been extended with commercially available cables.

For the monitor in

For the monitor in

landscape orientation

portrait orientation

 

 

 

 

 

 

 

 

1.Insert the anti-rotation protrusion of the mounting bracket into the anti-rotation hole of the monitor.

2.Secure the stand angling hole of the monitor with the mounting screw.

3.Adjust the angle of the remote control sensor box, and secure it with the fixing screw, so that it may accurately receive signals from the remote control unit.

Stand angling hole

Remote control sensor box

Angle

 

adjustment

 

Fixing screw

Anti-rotation hole

Anti-rotation protrusion

Mounting screw (short)

Mounting bracket

 

4.Insert the remote control sensor box connection cable into the control kit terminal.

Remote control sensor box

Control kit terminal Connection cable

TIPS

•When you connect the remote control sensor box, the brightness sensor can be used.

The screen brightness will automatically change according to lighting conditions and the surrounding brightness. (See page 25.)

•Depending on where it has been placed or the surrounding conditions, the remote control sensor box may be affected by the brightness of the main unit screen and the brightness sensor may respond.

•Do not install the remote control sensor box in extremely bright or dark areas. The brightness sensor may not function properly.

Brightness sensor

E14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PN-V600 Blue For Customers in U.KGREEN-AND-YELLOW BrownRefer Servicing to Qualified Service Personnel Important InformationEuropean Union Information on Disposal for Users private householdsInformation on Disposal for Business Users Other Countries outside the EUDear Sharp Customer Safety Precautions Fan in this product has a limited lifetime Use only the power cord supplied with the monitorRear side buttons Remote control unit buttons Mounting Precautions Contents Supplied ComponentsNRear view Part NamesNFront view 11 E Connecting Peripheral Equipment Connection when the PN-ZB02 optional is attachedMultiple monitor connection Connecting Peripheral Equipment13 E Connection with video cableSet the ID No Connection with the control kit optionalConnect the monitors in order Installing the batteries Preparing the Remote Control UnitConnecting the Power Cord Remote control operation rangeAffixing the Protection Covers Binding CablesRemoving the Handles Be sure the handles are attached securelyTurning power on/off Turning Power On/OffTurning on the main power Disabling power on/off operationsBasic Operation Input Input mode selectionVOL +/- Volume adjustment MuteDisplay 19 EBasic Operation Dot by Dot Basic Operation NSwitching the screen sizeWide Zoom Normal Cut offThis Monitor only Remote Control Mode21 E Specified MonitorNExample of operation Menu ItemsDisplaying the menu screen NMenu screen displayNSCREEN 23 EMenu item details Menu Items NPICTURENAUDIO NSETUPMenu Items 25 E Menu Items NOPTION Menu Items NPIP/PbyP 27 ENMULTI PIP Menu Items NDual screen displayNEnlarge NSCHEDULE NZOOM2 Special Setting29 E NScreen display for adjustment Adjustments for PC screen displayNAutomatic adjustment 31 E PC connection Communication procedureControlling the Monitor with a PC RS-232C Communication conditions33 E NCommunication intervalNID numbers NCommands for ID controlControlling the Monitor with a PC RS-232C Advanced operationVOLM0020 ← 35 ENRepeater control OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←NSaving the Gamma user data Setting of the Gamma user dataNTo transfer the Gamma user data NActivating the Gamma user dataHow to read the command table RS-232C command tablePower control/Input mode selection 37 EControlling the Monitor with a PC RS-232C Screen menu 39 E Controlling the Monitor with a PC RS-232C Picture menuSetup menu Controlling the Monitor with a PC RS-232C Audio menu41 E Controlling the Monitor with a PC RS-232C Option menuLandscape orientation Portrait orientation Image Position Epos settingControlling the Monitor with a PC RS-232C Multi menu Controlling the Monitor with a PC RS-232C PIP/PbyP menu Initialization/Functional Restriction Setting Function menu43 E Commands for setting of the Gamma user data Controlling the Monitor with a PC RS-232C Others45 E Settings to connect to a LANControlling the Monitor with a PC LAN To set on the monitorDefault Gateway 0.0 Controlling the Monitor with a PC LAN To set from a PCControlling the Monitor with a PC LAN 47 EControlling with a PC Standby mode, Power on is the only operation available Information about this monitor appearsDNS Server User Name / Password49 E Accept IP AddressAccount Name / Password Installation Information NAME/LOCATIONAuthentication Monitor NameCondition 51 ERecipient E-MAIL Addresses ConfirmationTrap Setting of Authentication Error Snmp SettingTrap Setting VersionTroubleshooting 53 ETroubleshooting NPN-ZR01 optional Product Specifications SpecificationsNPN-V600 Product Specifications 55 ENDDC plug and play Specifications NDimensional DrawingsNPower management Specifications NCompatible signal timing PC 57 ESpecifications NCompatible signal timing AV 59 E Mounting Precautions For Sharp dealers and service engineers PN-V600 Me EN11L1
Related manuals
Manual 44 pages 52.15 Kb
Top Page Image Contents