Sharp PN-V600 operation manual Controlling the Monitor with a PC RS-232C Audio menu, Setup menu

Controlling the Monitor with a PC (RS-232C)

AUDIO menu

Function	Command	Direction	Parameter	Reply	Control/Response contents	*1	*2
							(A)	(B)
TREBLE	AUTR	WR	-5-5	-5-5
						○	○	○
BASS	AUBS	WR	-5-5	-5-5
BALANCE	AUBL	WR	-10-10	-10-10
RESET	ARST	W	3			-

SETUP menu

Function		Command	Direction	Parameter		Reply	Control/Response contents	*1		*2
									(A)		(B)
OSD H-POSITION		OSDH	WR	0-100		0-100		○
OSD V-POSITION		OSDV	WR	0-100		0-100
MONITOR		STDR	WR	0-1		0-1	0: LANDSCAPE, 1: PORTRAIT	○
LANGUAGE		LANG	WR	14		14	ENGLISH
				1		1	DEUTSCH
				2		2	FRANÇAIS	○
				3		3	ITALIANO
				4		4	ESPAÑOL		○		○
				5		5	РУССКИЙ
				6		6
Power On Delay		PWOD	WR	0		0	OFF	○
				1-60		1-60	ON
OPERATION MODE		FNCM	WR	0-1		0-1	0: MODE1, 1: MODE2	○
STANDBY MODE		STBM	WR	0-1		0-1	0: STANDARD, 1: LOW POWER	○
							(“ERR" when SCHEDULE is effective or OFF is selected for LED.)
OFF IF NO OPERATION		ATOF	WR	0-1		0-1	0: OFF, 1: ON	○
HOT PLUG CONTROL (DVI)		HPCT	WR	0-1		0-1	0: OFF, 1: ON	○	-		○
HOT PLUG CONTROL (HDMI)		HPCH	WR	0-1		0-1	0: OFF, 1: ON	○	○		○
RS-232C/LAN SELECT		CTLS	WR	0-1		0-1	0 : RS-232C 1 : LAN	○	-		○
ID NUMBER	ID NO. SETTING	IDST	W	0-255			Sets the monitor’s ID number. (“0” means “no ID number”.)
			R			0-255	Returns the monitor’s ID number.
	ID NO. SETTING	IDSL	W	1-255			Sets a monitor ID number.
	(ONCE)						This ID number is only effective for the command immediately after this
							command.
				0			Clears the ID number if one has been designated.
	ID NO. SETTING	IDLK	W	1-255			Sets a monitor ID number.	○	○		○
	(SUBSEQUENT)						This ID number is effective for the next and all subsequent commands
							after this command.
				0			Clears the ID number if one has been designated.
	ID CHECK	IDCK	W	0	ID	: xxx	Displays monitor’s own ID number and the selected ID number on the
					IDLK	: yyy	screen.
	ID DISPLAY	IDDP	W	0-2			0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)
							(When the PN-ZB02 is attached, the IP address and MAC address are
							both displayed.)
BAUD RATE		BAUD	WR	0-2		0-2	0: 9600bps, 1: 19200bps, 2: 38400bps	○	○		○
HDMI AUTO VIEW		HDAW	WR	0-1		0-1	0: OFF, 1: ON	○	○		○
BRIGHTNESS SENSOR (When		OPTS	WR	0-2		0-2	0: OFF, 1: ON, 2: ON: DISPLAY	○	○		○
connected to the PN-ZR01 (optional)
only)
BRIGHTNESS	WHEN DARK:	OPSD	WR	0-99		0-99
SENSOR	AMBIENT
SETTING (When	BRIGHTNESS
connected to
	WHEN DARK:	OPDD	WR	0-30		0-30
the PN-ZR01	SCREEN
(optional) only)	BRIGHTNESS							○	○		○
	WHEN LIGHT:	OPSL	WR	1-100		1-100
	AMBIENT
	BRIGHTNESS
	WHEN LIGHT:	OPDL	WR	1-31		1-31
	SCREEN
	BRIGHTNESS
SETTING COPY MODE		CPMD	WR	0		0	Copy to all monitors.
				1-225		1-225	Copy to the monitor with the set ID Number.	○	○		○
SETTING COPY TARGET		CPTG	WR	0		0	Copies the PICTURE menu settings.
				1		1	Copies all the settings.
LOGO SCREEN		BTSC	WR	0-1		0-1	0: OFF, 1: ON

E40