Sharp PN-V600 Controlling the Monitor with a PC LAN, 45 E, Settings to connect to a LAN

Page 45

Controlling the Monitor with a PC (LAN)

When the PN-ZB02 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN.

You can also configure the monitor to send e-mail notification when it has a problem.

The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

Network (LAN)

LAN terminal

Hub

LAN cable (commercially available, straight)

TIPS

•You must assign an IP address to the monitor by following the procedures in “Settings to connect to a LAN”. (See the description on the right.)

•Your PC must be installed with Internet Explorer (version 7.0 or later).

•To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 24.)

•You cannot use RS-232C and LAN control simultaneously.

Initializing personal information

•When the PN-ZB02 (optional) is attached, personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET 1. (See page 31.) Note that ALL RESET 2 will not initialize e-mail addresses and other settings.

Settings to connect to a LAN

Set the monitor’s IP address and subnet mask to match the settings of your LAN.

These settings can be made on either the monitor or a PC connected to the monitor.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

■ To set on the monitor

Set RS-232C/LAN SELECT on the SETUP menu to LAN, and then set the LAN SETUP options. (See pages 24 and 25.)

After setting each item, select SET and press MENU .

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON.

To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

Press or to select items, and press or to change the values.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

Press or to select items, and press or to change the values.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway.

If you are not using a gateway, specify “0.0.0.0”.

Press or to select items, and press or to change the values.

RESET

Resets the values of the LAN settings to the factory preset values.

Select ON and then press MENU .

TIPS

•When manually setting the IP address, the IP address for secondary monitors connected by RS-232C can be automatically allocated. (See page 25.)

45 E

Page 44 Page 46
Image 45
Page 44 Page 46
Contents PN-V600 GREEN-AND-YELLOW For Customers in U.KBlue BrownImportant Information Refer Servicing to Qualified Service PersonnelInformation on Disposal for Business Users Information on Disposal for Users private householdsEuropean Union Other Countries outside the EUDear Sharp Customer Safety Precautions Use only the power cord supplied with the monitor Rear side buttons Remote control unit buttonsFan in this product has a limited lifetime Mounting Precautions Supplied Components ContentsPart Names NFront viewNRear view 11 E Connection when the PN-ZB02 optional is attached Connecting Peripheral Equipment13 E Connecting Peripheral EquipmentMultiple monitor connection Connection with video cableConnection with the control kit optional Connect the monitors in orderSet the ID No Connecting the Power Cord Preparing the Remote Control UnitInstalling the batteries Remote control operation rangeRemoving the Handles Binding CablesAffixing the Protection Covers Be sure the handles are attached securelyTurning on the main power Turning Power On/OffTurning power on/off Disabling power on/off operationsVOL +/- Volume adjustment Input Input mode selectionBasic Operation Mute19 E Basic OperationDisplay Wide Zoom Normal Basic Operation NSwitching the screen sizeDot by Dot Cut off21 E Remote Control ModeThis Monitor only Specified MonitorDisplaying the menu screen Menu ItemsNExample of operation NMenu screen displayMenu item details 23 ENSCREEN Menu Items NPICTURENSETUP Menu ItemsNAUDIO 25 E Menu Items NOPTION 27 E NMULTIMenu Items NPIP/PbyP Menu Items NDual screen display NEnlargePIP NZOOM2 Special Setting 29 ENSCHEDULE Adjustments for PC screen display NAutomatic adjustmentNScreen display for adjustment 31 E Controlling the Monitor with a PC RS-232C Communication procedurePC connection Communication conditionsNCommunication interval 33 EControlling the Monitor with a PC RS-232C NCommands for ID controlNID numbers Advanced operationNRepeater control 35 EVOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←NTo transfer the Gamma user data Setting of the Gamma user dataNSaving the Gamma user data NActivating the Gamma user dataPower control/Input mode selection RS-232C command tableHow to read the command table 37 EControlling the Monitor with a PC RS-232C Screen menu Controlling the Monitor with a PC RS-232C Picture menu 39 EControlling the Monitor with a PC RS-232C Audio menu Setup menuControlling the Monitor with a PC RS-232C Option menu 41 EImage Position Epos setting Controlling the Monitor with a PC RS-232C Multi menuLandscape orientation Portrait orientation Initialization/Functional Restriction Setting Function menu 43 EControlling the Monitor with a PC RS-232C PIP/PbyP menu Controlling the Monitor with a PC RS-232C Others Commands for setting of the Gamma user dataControlling the Monitor with a PC LAN Settings to connect to a LAN45 E To set on the monitorControlling the Monitor with a PC LAN To set from a PC Default Gateway 0.047 E Controlling with a PCControlling the Monitor with a PC LAN Information about this monitor appears Standby mode, Power on is the only operation available49 E User Name / PasswordDNS Server Accept IP AddressAuthentication Installation Information NAME/LOCATIONAccount Name / Password Monitor NameRecipient E-MAIL Addresses 51 ECondition ConfirmationTrap Setting Snmp SettingTrap Setting of Authentication Error Version53 E TroubleshootingTroubleshooting NPN-V600 Product Specifications SpecificationsNPN-ZR01 optional Product Specifications 55 ESpecifications NDimensional Drawings NPower managementNDDC plug and play 57 E Specifications NCompatible signal timing PCSpecifications NCompatible signal timing AV 59 E Mounting Precautions For Sharp dealers and service engineers PN-V600 Me EN11L1
Related manuals
Manual 44 pages 52.15 Kb
Top Page Image Contents