Sharp PN-V600 Specifications NDimensional Drawings, NPower management, NDDC plug and play

Page 56

Specifications

nDimensional Drawings

Note that the values shown are approximate values.

52-5/8 [1335.9]

Unit: inch [mm]

5-7/8

[149.3]

3-5/8

[92.3]

29-11/16 [754.2]

52-5/8 [1335.9]

Opening width (52-5/16 [1329.4])

Opening height (29-7/16 [747.7])

	VESA holes *	7-7/8	7-7/8
		[200]	[200]

3-15/16 3-15/16

[100] [100]

7-7/8 [200]

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws.

Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch

(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the monitor.

nPower management

This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in

order for the monitor’s power management function to work.

DPMS: Display Power Management Signaling

DPMS	Screen	Power	Hsync	Vsync
DPMS	Screen	consumption*1	Hsync	Vsync
ON STATE	Display	305 W	Yes	Yes

STANDBY	No		No	Yes
		1.0 W*2
SUSPEND		1.0 W*2	Yes	No
	display
OFF STATE	display		No	No
OFF STATE			No	No

*1 When PN-ZB02 (optional) is not connected.

*2 When AUTO INPUT CHANGE is set to OFF.

DMPM: Digital Monitor Power Management

DMPM	Screen	Power
DMPM	Screen	consumption*1
Monitor ON	Display	305 W
Active OFF	No display	1.0 W*2

nDDC (plug and play)

The monitor supports the VESA DDC (Display Data Channel) standard.

DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect plug-and-play monitors.

There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.

E56

Image 56

Contents PN-V600 For Customers in U.K GREEN-AND-YELLOWBlue BrownRefer Servicing to Qualified Service Personnel Important InformationInformation on Disposal for Users private households Information on Disposal for Business UsersEuropean Union Other Countries outside the EUDear Sharp Customer Safety Precautions Fan in this product has a limited lifetime Use only the power cord supplied with the monitorRear side buttons Remote control unit buttons Mounting Precautions Contents Supplied ComponentsNRear view Part NamesNFront view 11 E Connecting Peripheral Equipment Connection when the PN-ZB02 optional is attachedConnecting Peripheral Equipment 13 EMultiple monitor connection Connection with video cableSet the ID No Connection with the control kit optionalConnect the monitors in order Preparing the Remote Control Unit Connecting the Power CordInstalling the batteries Remote control operation rangeBinding Cables Removing the HandlesAffixing the Protection Covers Be sure the handles are attached securelyTurning Power On/Off Turning on the main powerTurning power on/off Disabling power on/off operationsInput Input mode selection VOL +/- Volume adjustmentBasic Operation MuteDisplay 19 EBasic Operation Basic Operation NSwitching the screen size Wide Zoom NormalDot by Dot Cut offRemote Control Mode 21 EThis Monitor only Specified MonitorMenu Items Displaying the menu screenNExample of operation NMenu screen display23 E Menu item detailsNSCREEN Menu Items NPICTURENAUDIO NSETUPMenu Items 25 E Menu Items NOPTION Menu Items NPIP/PbyP 27 ENMULTI PIP Menu Items NDual screen displayNEnlarge NSCHEDULE NZOOM2 Special Setting29 E NScreen display for adjustment Adjustments for PC screen displayNAutomatic adjustment 31 E Communication procedure Controlling the Monitor with a PC RS-232CPC connection Communication conditions33 E NCommunication intervalNCommands for ID control Controlling the Monitor with a PC RS-232CNID numbers Advanced operation35 E NRepeater controlVOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Setting of the Gamma user data NTo transfer the Gamma user dataNSaving the Gamma user data NActivating the Gamma user dataRS-232C command table Power control/Input mode selectionHow to read the command table 37 EControlling the Monitor with a PC RS-232C Screen menu 39 E Controlling the Monitor with a PC RS-232C Picture menuSetup menu Controlling the Monitor with a PC RS-232C Audio menu41 E Controlling the Monitor with a PC RS-232C Option menuLandscape orientation Portrait orientation Image Position Epos settingControlling the Monitor with a PC RS-232C Multi menu Controlling the Monitor with a PC RS-232C PIP/PbyP menu Initialization/Functional Restriction Setting Function menu43 E Commands for setting of the Gamma user data Controlling the Monitor with a PC RS-232C OthersSettings to connect to a LAN Controlling the Monitor with a PC LAN45 E To set on the monitorDefault Gateway 0.0 Controlling the Monitor with a PC LAN To set from a PCControlling the Monitor with a PC LAN 47 EControlling with a PC Standby mode, Power on is the only operation available Information about this monitor appearsUser Name / Password 49 EDNS Server Accept IP AddressInstallation Information NAME/LOCATION AuthenticationAccount Name / Password Monitor Name51 E Recipient E-MAIL AddressesCondition ConfirmationSnmp Setting Trap SettingTrap Setting of Authentication Error VersionTroubleshooting 53 ETroubleshooting Specifications NPN-V600 Product SpecificationsNPN-ZR01 optional Product Specifications 55 ENDDC plug and play Specifications NDimensional DrawingsNPower management Specifications NCompatible signal timing PC 57 ESpecifications NCompatible signal timing AV 59 E Mounting Precautions For Sharp dealers and service engineers PN-V600 Me EN11L1

Related manuals

Manual 44 pages 52.15 Kb