LG Electronics 19MB35PM, 23MB35PM, 22MB35PM owner manual Mounting on a wall, Model

Page 11

10ASSEMBLING AND PREPARING

ENGLISH

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

10 cm

10 cm

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.

When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

1Please, Use the screw and wall mount interface in accordance with VESA Standards.

2If you use screw longer than standard, the monitor might be damaged internally.

3If you use improper screw, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

4VESA compatible.

5Please use VESA standard as below.

y y784.8 mm (30.9 inch) and under

*Wall Mount Pad Thickness : 2.6 mm * Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

y y787.4 mm (31.0 inch) and above

*Please use VESA standard wall mount pad and screws.

Model

19MB35PM

22MB35PM

 

23MB35PM

 

VESA (A x B)

75 x 75

100 x 100

Standard screw

M4

 

Number of screws 4

 

CAUTION

y yDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.

y yIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.

y yUse only an authorized LG wall mount and contact the local dealer or qualified personnel.

y yDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.

y yUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

NOTE

y yUse the screws that are listed on the VESA standard screw specifications.

y yThe wall mount kit will include an installation manual and necessary parts.

y yThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.

y yThe length of screws may differ depending on the wall mount. Be sure to use the proper length.

y yFor more information, refer to the instructions supplied with the wall mount.

Image 11
Contents IPS LED Monitor LED LCD Monitor Page Contents SUB Cable DVI-D Cable Power Cord Stand Base Audio CableAssembling and Preparing UnpackingParts and buttons Power IndicatorStand Body Stand Base Setting up the Monitor setAttaching the Stand Base Detaching the stand baseDetaching the stand body Rear Side Front Side Adjusting the angleMounting on a table Stand Body Tape Locking Pin Adjusting the stand heightUsing the Kensington locking device Head section Stand section Using the Pivot functionSwivel stand Vesa a x B 75 x 100 x Standard screw Number of screws Mounting on a wallModel DVI-D connection Using the Monitor SETConnecting to a PC SUB connection‘AUTO’ Function YSelf Image Setting FunctionPeripheral device connection Button Customizing SettingsPower Indicator Monitor set ButtonsEnvironment Customizing SettingsMenu Settings Menu Analog DigitalPicture Six Color Color ResetMenu Next Menu Color Description Gamma Color Temp CustomNoise and clear or sharpen the image of characters Display~ 24 hours OthersReader Off Reader SettingReader Mode Description ReaderLow Off Disables Super Energy SavingDisplay the Super Energy Saving OSD HighDo you see a OSD Locked message on the screen? TroubleshootingCheck Control Panel Display Settings and adjust the display No image appearsRecommend resolution Settings19MB35PM Specifications22MB35PM 23MB35PM Horizontal Vertical PolarityH/V FrequencykHz FrequencyHz Preset Modes ResolutionIndicator Mode LED ColorProper Posture Proper posture for using the Monitor setDeclaration of Conformity