Marantz PM6005 appendix Specifications

Page 41

Contents

Connections

Playback

Settings

Tips

Appendix

Specifications

RMS Power output

 

(20 Hz – 20 kHz simultaneous drive of both channels) :

45 W x 2 (8 Ω/ohms load)

Total harmonic distortion

60 W x 2 (4 Ω/ohms load)

 

(20 Hz – 20 kHz simultaneous drive of both channels,

 

8 Ω/ohms load) :

0.08 %

Output band width (8 Ω/ohms load, 0.06 %) :

10 Hz – 50 kHz

Frequency response (CD, 1 W, 8 Ω/ohms load) :

10 Hz – 70 kHz +0 dB, –1 dB

Dumping factor (8 Ω/ohms load, 40 Hz – 20 kHz) :

100

Input sensitivity/Input impedance

 

PHONO (MM) :

2.2 mV/47 kΩ/kohms

CD, TUNER, NETWORK, RECORDER :

200 mV/20 kΩ/kohms

Maximum allowable PHONO input level (1 kHz) MM :

100 mV

RIAA deviation (20 Hz – 20 kHz) :

±1.0 dB

S/N (IHF-A, 8 Ω/ohms load)

 

PHONO (MM) :

83 dB (5 mV input, 1 W output)

CD, TUNER, NETWORK, RECORDER :

102 dB (2 V input, Rated output)

Tone control

 

Bass (50 Hz) :

±10 dB

Treble (15 kHz) :

±10 dB

Digital input

 

Coaxial :

0.5 Vp-p

Optical :

–27 dBm or later

Power requirement :

AC 120 V, 60 Hz

Power consumption (UL60065) :

155 W

Power consumption in standby mode :

0.3 W

For the purpose of improvement, the specifications and design are subject to change without notice.

 

 

 

 

 

 

 

 

41

 

 

Front panel

 

 

Rear panel

 

 

Remote

 

Index

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 41
Contents PM6005 Contents Setting the remote signal receiving function SettingsAccessories Front panel Rear panel Remote Index High quality sound FeaturesEasy operation High performanceDigital Input Coaxial, Optical Tone control functionI o Part names and functionsFront panel Rt y uio Q0 Rear panel Amplifier and Tuner operation Remote control unitQ1 W0 Q2 W1 QPOWER button WRemote mode select buttonCD player operation Q5 y Network audio player operationConnecting the power cord vpage Connecting devices with remote control connectorsAudio cable Remote connector Cable ConnectionsSpeaker connection Connecting the speakers cablesSpeaker A/B connection Speaker R Speaker L Bi-wiring connectionTurntable Connecting a playback deviceCD player Player Recording device Connecting a recording deviceDevices with digital Audio connectors Connecting a TV/Devices with digital audio connectorsRemotely connecting Marantz devices Connecting devices with remote control connectorsNnSWITCHED Connecting the power cordNnUNSWITCHED 22Connection to the AC outletPlayback 22Turning the power off Turning the power onAMP Power Direct Volume df MuteAdjusting the tone Adjusting the volumeSelecting the speakers for audio output Selecting the input sourcePlaying CDs 22Playback in source direct mode22Playback in Loudness mode Recording starts RecordingSettings Turning Auto Standby mode off Setting the Auto Standby modeTurning Auto Standby mode on To turn the Auto Standby mode offSpeakers a Speakers B Setting remote control codes for the remote control Setting remote control codes22To set the remote control codes to AMP2 22To set the remote control codes to AMP3Hold down Remote Mode CD and press Enter Setting remote control codes for this unitTips ContentsTips Want to adjust the tone myselfWant to play back high quality television sound Want sound playback that is faithful to the original soundSymptom Cause / Solution Troubleshooting22Power does not turn on / Power is turned off Symptom ContentsConnectionsPlaybackSettingsTipsAppendix 22No sound comes out 22Sound is interrupted or noise occurs 22Desired sound does not come outPlayback on devices that have digital audio terminals AppendixExplanation terms 22Supported audio formatsSpecifications Index 22Dimensions 22Weight 16 lbs 12 oz 7.6 kgHoldings Inc 10289 00AM
Related manuals
Manual 10 pages 28.75 Kb