Sharp XLDH259P Timer and sleep operation Remote control only, Setting the clock, Timer playback

Setting the clock (continued)

5To adjust the minutes, press the or button and

then press the MEMORY button. Press the or button once to advance the time by 1 minute.

To confirm the time display:

Press the CLOCK/TIMER button. The time display will appear for about 5 seconds.

Note:

The “CLOCK” will appear or time will be displayed when the AC power supply is restored after a power failure or unplugging the unit. If incorrect, readjust the clock as follows.

To readjust the clock:

Perform “Setting the clock” from step 1. If the “CLOCK” does not appear in step 2, step 3 (for selecting the 24-hour or 12-hour display) will be skipped.

To change the 24-hour or 12-hour display:

1Clear all the programed contents. [Refer to “Factory reset, clearing all memory” on page 14 for details.]

2Perform “Setting the clock” from step 1 onwards.

Timer and sleep operation (Remote control only)

Once timer:

Once timer play works for one time only at a preset time.

Daily timer:

Daily timer play works at the same preset time every day that we set. For example, set the timer as a wake-up call every morning.

Using the once timer and daily timer in combination:

For example, use the once timer to listen a radio program, and use the daily timer to wake up.

	1 minute or more
Daily timer			Once timer
Start	Stop	Start	Stop

QTimer playback

Before setting timer:

OCheck that the clock is set to the correct time (refer to page 11-12). If it is not set, you cannot use the timer function.

OFor timer playback: Plug in USB or load discs or dock iPod to be played.

1Press the ON/STAND-BY button to turn the power on.

2Press and hold the CLOCK/TIMER button.

3Within 10 seconds, press the or button to select “ONCE SET” or “DAILY SET”, and press the MEMORY button. Set the clock to the correct time if “ONCE SET” or “DAILY SET” does not appear.

4Within 10 seconds, press the or button to select “TIMER SET”, and press the MEMORY button.

5To adjust the hour, press the or button and then press the MEMORY button.

6To adjust the minutes, press the or button and then press the MEMORY button.

7Set the time to finish as in steps 5 and 6 above.

8To select the timer playback source (CD, TUNER, USB,

iPodor AUDIO IN), press the or button. Press the MEMORY button.

When you select the tuner, select a station by pressing the or button, and then press the MEMORY button. If a station has not been programmed, “NO PRESET” will be displayed and timer setting will be cancelled.

9Adjust the volume using the VOLUME control, and then press the MEMORY button. Do not turn the volume up too high.

10Press the ON/STAND-BY button to enter the power stand-by mode. The “TIMER” indicator lights up and the unit is ready for timer playback.

11 When the preset time is reached, playback will start. The volume will increase gradually until it reaches the preset volume. The “” indicator will blink during once timer playback. The “DAILY” indicator will blink during daily timer playback.

12When the timer end time is reached, the system will enter the power stand-by mode automatically.

Once timer:

The timer will be cancelled.

Daily timer:

The timer operates at the same time every day. It will continue until the daily timer setting is cancelled. Cancel the daily timer when it is not in use.

Notes:

OWhen performing timer playback using another unit connected to the USB terminal or AUDIO IN socket, select “USB” or “AUDIO IN” in step 8.

OThis unit will turn on or enter the power stand-by mode automatically. However, the connected unit will not turn on or off. To stop the timer playback, follow step “Cancelling the timer setting” of this page.

Checking the timer setting:

1Turn the power on and press and hold down the CLOCK/ TIMER button.

2Within 10 seconds, press the or button to select “ONCE SET” or “DAILY SET”, and press the MEMORY button.

3Within 10 seconds, press the or button to select “TIMER CALL”, and press the MEMORY button.

Canceling the timer setting:

1Turn the power on and press and hold down the CLOCK/ TIMER button.

2Within 10 seconds, press the or button to select “ONCE SET” or “DAILY SET”, and press the MEMORY button.

3Within 10 seconds, press the or button to select “TIMER OFF”, and press the MEMORY button. Timer will be canceled (the setting will not be canceled).

Reusing the memorized timer setting:

The timer setting will be memorized once it is entered. To reuse the same setting, perform the following operations.

1Turn the power on and press and hold down the CLOCK/ TIMER button.

2Within 10 seconds, press the or button to select “ONCE SET” or “DAILY SET”, and press the MEMORY button.

3Within 10 seconds, press the or button to select “TIMER ON”, and press the MEMORY button.

4Press the ON/STAND-BY button to enter the power stand- by mode.

E-12