Kenwood CT/KXF-W instruction manual Recording of CD playback Ccrs Deck B only, How to cancel Ccrs

Convenient CD recording (CT-203/KXF-W4010; Deck B only)

CT-2050/203/KXF-W6010/W4010 (En/M)

When connected with a KENWOOD amplifier,CD player provided with "f", "Ä", " (Ä)" marking through the

22 system control cord, this unit allows to use the CCRS, which starts recording automatically after setting the optimum recording level for the CD and tape to be used in recording.

Since this unit is not designed for recording with metal (TYPE ) tapes, do not use metal tapes for recording.

Preparation 1Complete the connections referring to

"System connections". 6

2(Set the input selector of the amplifier to

CD.)

3(Load a disc in the CD player.)

(Edit tracks as required on the CD player.)

: Keys and control used in the operations described on this page.

Recording of CD playback (CCRS) (Deck B only)

1

2

Insert a tape in deck B.

Determine the recording condition.

ÖFor the tape direction setting, see the description below “Select the

tape transport direction”. 0

1Select the recording mode.

REV.MODE

2Select the Dolby NR mode.

DOLBY NR

Each press switches the indication.

1 “[” :Double-side recording.

2“Ó” :(Tape also stops after having recorded both sides.)

3 “Ò” :One-way recording.

Each press switches the indication.

1 DOLBY NR “OFF” (extinguished): Dolby NR is not used.

2DOLBY NR “B”: Noise reduction of the ordinary type.

3DOLBY NR “C”: Noise reduction with higher performance.

3Press the CCRS key.

CT-2050/KWF-W6010

CCRS

CT-203/KXF-W4010

ÖProgram-edit recording is not possible when tracks of more than one CD are programmed using a Carrousel type CD player.

ÖWhen performing CCRS recording with a CD player which can be loaded multiple compact discs, set the CD palyer to TRACK mode, press the disc selector key and press the CCRS key of the cassette deck.

ÖThe CCRS indicator blinks, and actual recording starts in about 20 to 200 seconds (after creating a non-recorded blank of about 8 seconds).

How to cancel CCRS

During recording level setting:

Press the Stop key of the CD player or the stop key of the cassette deck.

During CCRS recording:

Press the Stop key of the CD player, then press the OPEN / CLOSE key of the CD player.

After completion of CCRS recording:

Press the OPEN / CLOSE key of the CD player.

ÖAfter recording, the cassette deck and CD player enter the stop mode automatically.

ÖAfter completion of CCRS recording , be sure to cancel the CCRS and ensure that the CCRS indicator has gone off.

	1. If the CCRS key is pressed during CD playback, playback stops and CCRS operation begins.
	2 .If the remaining amount of tape is small, CCRS may not function correctly or CCRS operation may be canceled in mid-operation.
	3 .Once the CCRS recording level has been set, the recording balance and recording level cannot be adjusted while the CCRS operation
	is being carried	out.
Notes	4 .The CCRS function sets the peak level for the entire CD in approx. 20~200 seconds. On very rare occasions, however, the function
	may not be able to set the optimum recording level. If this occurs, carry out recording manually referring to the “Normal recording”
	section.	^
	5. The CCRS recording level setting is canceled when the open/close key of the CD player is pressed or when the power is switched OFF.

6. With CD players equipped with the EDIT function, it is possible to make recordings in which the last songs on sides A and B are not cut off in the middle and in which the recording capacity of the tape is used to the fullest extent. (Set the REV.MODE key of the deck to “[”.)