I99 H1X18VX- Stereo

Buttons and their Functions on the Receiver

Examples:
IF 1:	Entry:	Indication:
1200 MHz	01200	11200 Mz
950 MHz	00950	10950 Mz

Please also observe setting of the video deviation –1, –2 or –3 (see paragraphe "¢Video – Adjusting the Video Deviation").

¢V/H – Selecting Vertical/Horizontal Polarization and Input A/B

Press the ¢V/H button to indicate the current polarization in the display, e.g., (H1 18 V)

TIMER o p ü +

SIGNAL IIIIIIIIIIIII

With the ¢</ > buttons, you can select between V1, H1, V2, and H 2.

Allocation of the respective LNC voltage depends on the selected LNC system (see paragraphe "Setting Zero Position and Limits").

For LNC´s with magnetic polarizer, the optimum skew value must be adjusted after having selected the polarization (see also paragraphe "SKEW ALL – Transferring the Skew Value").

Press the ¢V/H button once again to indicate on the display the input which is to be selected with the ¢</ > buttons ("INPUT A" or "INPUT B"). See also the sections "Adap- ting the Polarizer, Installation Menu", and "Selecting the Aerial Input".

¢VIDEO – Adjusting the Video Deviation

The frequency-modulated satellite signals are transmitted with different deviations. To obtain a good picture, the recei- ver must be adjusted correspondingly.

Press the ¢VIDEO button to indicate on the display the video deviation and video polarity, e.g., (DEV. 3).

TIMER o p ü +

I99 DEV. X3XX STEREO

SIGNAL IIIIIIIIIIIII

The video deviation is selected with the ¢</ > buttons:

DEV. 1	= 25 MHz,	DEV. –1 = 25 MHz,
DEV. 2	= 22.5 MHz,	DEV. –2 = 22.5 MHz,
DEV. 3	= 16 MHz,	DEV. –3 = 16 MHz.

For C-band and S-band reception with 4- resp. 2.5GHz LNC´s, the video signal must be inverted by selecting the set- ting DEV. –1 … DEV. –3.

¢AUDIO – Mono/Stereo and Sound Carrier Switching

Press the ¢AUDIO button to indicate the current audio mode in the display, for example:

TIMER o p ü +

I99 MONOX <X > STEREO

SIGNAL IIIIIIIIIIIII

By repeatedly pressing the ¢AUDIO button, you can select between:

MONO < > = Main carrier, Mono wide,

MONO > < = Subcarrier, Mono Panda Wegener, STEREO = Panda carrier*, Stereo.

On STEREO, the indication "STEREO" appears in addition on the display ´` of the receiver. Press the ¢< or ¢> but- ton to indicate the actual value of the set frequency, for exam- ple:

TIMER o p ü +

I99 X7 . 02MH z STEREO

SIGNAL IIIIIIIIIIIII

You can adjust the frequency between 5.00 MHz and 9.99 MHz in steps of 10 k Hz.

Pressing and holding down the ¢< or ¢> button will scan the frequencies at high speed.

Direct frequency entry is possible with the numeric buttons of the remote control handset. Tuning will be effected only after having entered the third frequency digit.

¢</ > – Down/Up Setting Buttons

When in programme mode, use the ¢</ > buttons to select the next programme position down or up.

In the other modes, the ¢</ > buttons are used for chan- ging the entered data.

When holding down the corresponding button, the program- me positions or data values are selected and displayed at high speed.

When in standby, pressing the ¢</ > buttons will switch to the last selected SAT programme position (Last Station Memory).

¢MEMORY – Storing Data in Memory

Pressing the ¢MEMORY button stores all data in memory.

*Panda/Wegener Communications Inc.. Award for highest tone quality.