Blaupunkt PCA 2100, PCA 250 manual Connections & Controls, +12, TriggerFuse, Power Connections

Page 8

CONNECTIONS & CONTROLS

 

 

 

 

 

 

 

 

 

 

Speaker Outputs

Ground

 

+12

 

 

 

 

 

 

 

(Battery)

 

 

 

 

 

 

 

 

 

 

TriggerFuse

POWER CONNECTIONS:

GROUND - This is the high current ground connection to the chassis of the car. It should be fastened to a clean ground connection in the vehicle, capable of handling high current loads. This wire should be no longer than 3 feet (1 meter)

+12v - A high current line run direct from the batter is highly recommended to insure adequate current and voltage. This line MUST be run through a dedicated fuse of some kind and this fuse should be located immediately next to the power source. This in-line fuse is used to protect the vehicle should a short to chassis occur.

TRIGGER - This line tells the amp to turn on and is remotely switched from the radio which normally provides an amp “trigger” output. This line is required to go “high” (+12V) to turn on the amp. If this line is not available, use the power antenna line trigger which is normally available in most radios.

FUSE - This fuse is only for catastrophic situations should the amplifier begin to self-destruct or incur installation situations where gross amounts of current are being required from the amp beyond its design limits. Although another fuse should be installed inline with the high power line at the battery, this amplifier mounted fuse MUST remain in the circuit to protect the amplifier.

Power Terminal (+12V)

Connect directly to the vehicle battery (+) terminal with 10 gage wire (minimum)

 

NOT SUPPLIED

To Battery

Fuse or

Terminal

Circuit Breaker

10 Gage

Battery

Wire

Terminal

 

Adapter

Ground Terminal

Connect to a good chassis ground. The ground connection should be clean, unpainted metal to provide a good electrical connection.

SPEAKER OUTPUTS - The amplifier is connected to appropriate impedance speakers via these leads. It is IMPERATIVE that these leads NOT be connected or touch the vehicle chassis in any way or the amplifier will be damaged. The (+) and (-) leads of the amp are in no way inter-connected to one another. Also, NONE of the leads can touch each other, touch ground, or touch +12V or damage may occur to the amp or vehicle.

10 Gage

Wire

Sheet

Metal

Screw

Ring

Connector

Drill 1/8” hole

in chassis

sheet metal

Remote Terminal

Connect the radio power antenna lead from

the receiver to the amplifier terminal. This turns the amplifier on whenever the receiver is turned on.

 

 

 

 

 

 

 

Butt

 

To Receiver

 

 

Connector

 

(not supplied)

 

Power

 

Antenna Lead

 

 

 

 

 

18-20 Gage

 

 

 

 

 

Wire

 

 

 

 

 

 

 

 

6

Image 8
Contents Page PARAMETER/FEATURE Table of Contents IndiceTable DES Matières Índice DAS MatériasPCA Amplifier Benefits & Features Thank YOU for Choosing BlaupunktSafety Concerns Installation WarningsInstallation Tools System PlanningVehicle Wiring Vehicle FusingPower Connections Connections & Controls+12 TriggerFuseGain Control Power On Line Level InputBass Boost Low-Pass FrequencySystem Configuration #1 System Configuration #2System Configuration #3 System Configuration #4TROUBLE-SHOOTING Guide Symptom Probable Cause or CorrectionLimited Warranty Information United States only Blaupunkt Technical SupportMerci D’AVOIR Choisi Blaupunkt Avantages ET Propriétés DES Amplificateurs PCAAvertissements Relatifs À L’INSTALLATION Consignes DE SécuritéOutils D’INSTALLATION Planification DU SystèmeCâblage DU Véhicule Pose DE Fusibles SUR LE VéhiculeCâblage DE L’ALIMENTATION Câblage DES HAUT-PARLEURSConnexions & Commandes Prise pour enceintes+12 Batterie DéclencheurFusible Connexions D’ALIMENTATIONEntrée haut-niveau Réglage deVoyant de mise Sous tension FréquenceConfiguration DE Système N Mode 1 canal avec subwoofer ponté Guide DE Dépannage Symptôme Cause Proble OU CorrectionInformations SUR LA Garantie Limitée États-Unis seulement Assistance Technique DE BlaupunktLE Agradecemos QUE Haya Escogido Blaupunkt Beneficios Y Funciones DEL Amplificador Tipo PCAConsideraciones DE Seguridad Precauciones DE InstalacionesPlanificacion DEL Sistema Herramientas Para LA InstalacionAlambrado EN EL Vehiculo Fusibles EN EL VehiculoAlambrado DE Potencia Alambrado DE LOS AltavocesConexiones Y Controles Salidas de la BocinaDisparadorFusible Conexiones DE PotenciaLuz LED de Encendido Configuracion DEL Sistema #1 Configuracion DEL Sistema #2Configuracion DEL Sistema #3 Configuracion DEL Sistema #4Resolucion DE Problemas Simtoma Causas Probables O Accion CorrectivaApoyo Tecnico DE Blaupunkt Obrigado POR Escolher Blaupunkt Características E Vantagens do Amplificador PCAMedidas DE Segurança Advertências Para a InstalaçãoPlanejamento do Sistema Ferramentas DE InstalaçãoFiação do Veículo Instalação DOS Fusíveis no VeículoFios Elétricos Fios Para OS ALTO-FALANTESEntradas E Controles Disparo+12Ligação Conexão DE ForçaControlo de Ganho Alimentação Ligada Conexões Elétricas E Saídas DOS ALTO-FALANTESEntrada de Nível de Linha Sistema DE Configuração No Modo Duplo de Alto-Falantes de Freqüências Graves de Canais Guia Para Solução DE Problemas Sintoma Causa Provável Ação CorretivaApoio Técnico Blaupunkt Assembly & Mounting

PCA 2100, PCA 250 specifications

Blaupunkt is a brand synonymous with quality audio equipment, and two of its standout amplifiers are the PCA 250 and PCA 2100. These models have garnered attention for their impressive specifications and advanced technologies that cater to audio enthusiasts looking for top-notch sound performance.

The Blaupunkt PCA 250 is a compact amplifier that packs a punch with its powerful output, making it perfect for a variety of audio applications. With a peak power output of around 250 watts, it delivers rich, distortion-free sound that elevates the listening experience. One of the main features of the PCA 250 is its Class D amplification technology, which not only ensures efficiency but also minimizes heat generation. This allows the amplifier to work effectively without the requirement for extensive cooling systems, making it suitable for tight spaces.

Another notable characteristic of the PCA 250 is its built-in crossover features, which enable users to customize audio frequencies. This ensures that high frequencies remain crisp while low frequencies are deep and powerful, providing a balanced sound spectrum. Additionally, the PCA 250 supports multiple input options, allowing for versatile connectivity with various audio sources, including professional audio gear and home entertainment systems.

On the other hand, the PCA 2100 takes the capabilities of amplification even further. With a peak power output of 1000 watts, this model is engineered for higher performance demands. It employs advanced circuitry that optimizes signal processing, ensuring minimal noise and maximum clarity. Like the PCA 250, it also features Class D technology for efficient power consumption.

The PCA 2100 stands out for its robust construction, designed to handle demanding environments while delivering top-quality sound. It also features adjustable gain controls, allowing users to tailor the output to their specific needs. This flexibility makes the PCA 2100 suitable for both professional DJs and home audio enthusiasts.

Both models incorporate thermal protection and short circuit protection technologies, safeguarding against possible damage from overload or overheating. This ensures reliability and longevity in performance, giving users peace of mind while enjoying their audio.

In conclusion, the Blaupunkt PCA 250 and PCA 2100 offer a combination of powerful amplification, advanced features, and durable construction. These amplifiers cater to a range of audio needs, making them ideal choices for those seeking superior sound quality and reliability in their audio equipment. Whether for home use or professional settings, Blaupunkt’s PCA series continues to establish a solid reputation in the audio industry.