Arcam AVR400 manual Other Connectors

Page 19

other

connectors

NOTE

Sockets referring to ‘Z2’ relate to connections used in multi-room installation. For more information on these connectors, see page E-46.

English

Data connectors

rLead/irDock

For use with an Arcam rLead or irDock accessory. See page E-15 and the accessory documentation for details.

RS232 serial connector

Use with control devices having an RS232 serial port (for example, Crestron and AMX touch screen controllers).

Network connector

This section deals with installation of the unit into an existing home network. For

information on how to use the

AVR400’s network features,

the USB socket, and for a list

of supported file types, refer to page E-45.

Networking is a large subject

and only the briefest guidelines are presented in this handbook. Please contact your Arcam dealer or specialist installer for more information about introducing the AVR400 into your computer network.

Ethernet

If an Ethernet cable is connected, the AVR400 will automatically attempt to connect to your network.

You should use CAT5 cable plugged into the RJ45 socket labelled ETHERNET on the rear panel.

If your network uses static IP addressing rather than DHCP, you will need to provide IP address, gateway, DNS and proxy information. See page E-39 for information on setting up the network.

USB connector

The AVR400 can play files

stored on a USB mass storage

device, typically a pen drive, but any USB device that complies with the ‘mass storage device‘ class is compatible.

The AVR400 only supports the direct connection of USB devices and will not support devices connected through a hub. If regular access to the USB socket is required, you may find it convenient to use a USB extension lead.

See page E-45 for details of supported file types.

Trigger connectors

The trigger connectors (Trig Z1 and Trig Z2) provide an electrical signal

whenever the AVR400 is switched on and the relevant zone enabled.

The trigger signal can be used to switch on and off compatible pieces of home

entertainment equipment, for example, you could set up a trigger to turn on your television and BD player whenever the

AVR400 was switched on.

There are two trigger output sockets on the AVR400, each capable of outputting a 12V, 70mA switching signal. The socket is designed for mono 3.5mm jacks: tip is the trigger output, sleeve is ground.

tip: Trigger output sleeve: Ground

TRIG Z1

Use for remotely turning on and off power amps or source equipment for Zone 1. On = 12V, Off = 0V.

TRIG Z2

Use for remotely turning on and off power amps or source equipment for Zone 2. On = 12V, Off = 0V.

Infra-red (IR) connectors

The infra-red inputs (Z1 IR and Z2 IR) allow the connection of external IR receivers, either when the AVR400 front panel IR receiver is fully or partially obstructed or to allow the use of a remote control in Zone 2.

There are two IR inputs on the AVR400, each designed for stereo or mono 3.5mm jacks. Tip is the modulated signal, sleeve is ground.

tip: Modulated signal sleeve: Ground

Z1 IR

This input is intended for use with a local IR receiver when the front panel of the AVR400 is blocked.

Connecting an IR receiver to Z1 IR will disable to front panel IR receiver to prevent problems with multiple commands if the front panel IR receiver is only partially obstructed.

Z2 IR

This input is intended for use with an IR receiver in Zone 2 to allow remote control of AVR400 from a second room.

A supplier of infra-red receivers and emitter accessories and systems is Xantech. See www.xantech.com for more information, or ask your Arcam dealer.

NOTE

The IR inputs on the AVR400 are designed for modulated signals. If the external IR receiver demodulates the IR signal, it will not work. Also the AVR400 does not provide power for external receivers on the IR jack, therefore an external power source will be required.

E-17

Image 19
Contents N d b o o k AVR surround amplifier Page English Important safety instructions SafetyClass II product Important notice Do not modify this product Safety information For European CustomersEnglish FCC Information for US customers 1. ProductPage Welcome ContentsProfessional Installation? DIY setup?Before you Begin… Interconnect cables PowerStandby power Placing the unitTrademark acknowledgements Preamplifier output Audio connectorsDigital connectors Speaker connectorsGeneral Hdmi connectorsMaking connections Digital audio connectors English Component/RGB video connectors Zone 2 connectorsLong cables or several inputs in parallel if required MCH input Analogue audio inputs Front panel AUX inputAnalogue pre-amplifier outputs Front panel Phones socketEnglish BD/SAT Blu-ray Disc Bd / DVD playerSatellite receiver CD playerConnecting an iPod using the Arcam irDock Aerial connectors Radio ConnectorsOther Connectors Surround back left and right Surround left and right SpeakersCentre Subwoofer Front left and rightBi-Amping the Front Left & Right speakers Connecting speakersUsing external power amplifiers Connecting subwoofersSelecting a source Switching onOperation Operating your AVR400Extended front panel menu Using ZoneUpdating firmware via USB Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesIPod commands AMP AMP Device ModeDVD DVD/BD Device Mode TUN TUN Device ModeNetwork commands Duplicates function of YELlOW key for some SAT SAT Device ModeAV AV Device Mode AVR400 AVR400.SHIFT + Hselects AUX input onVCR VCR Device Mode PVR PVR Device ModeCD CD Device Mode English Speaker Levels Essential SetupSpeaker types Speaker DistancesProblems Auto speaker SetupUsing a subwoofer Navigating the setup menu Setup menusTreble Bass Input ConfigGeneral information and system controls General SetupAuto Setup Off default no audio compression is appliedSpkr Levels None speaker not present in your configurationSpkr Types Spkr DistanceVideo Outputs Video InputsMode Network Zone SettingsIntroduction Decoding ModesTwo-channel source modes For Dolby Digital sources High resolution audio sourcesMulti-channel source modes Decoding modesCalibration Offset SettingsVolume Leveller Dolby Volume is a sophisticated newEnglish Tuner Operation Tuning/Channel SelectionSaving and selecting Presets Deleting PresetsInternet radio stations Network/usb OperationSelecting the playback source USB playbackZone Multi-room Set upZone 2 control connections Multi-room connection guide Code Learning Customising CR102Creating Macros Volume punch-throughKey Mover Copy a key between Device Modes Mode MoverLocking/Unlocking a specific Device Mode To restore a moved Device Mode key to its original stateResetting the CR102 Mode key IR punch-throughProblem Check that Or DTS decoding modes Switched offWired network Network hardware SpeakersContinual improvement policy SpecificationsProblems? Product GuaranteeWorldwide Guarantee Claims under guaranteePage Code Tabelle für Fremdgeräte Tabellen Apparaatcodes Device code TablesHYD GBCGEC HCMRCA NU-TECOKI RBMAVP YU-MA-TUGPX UPC STSADB NTLAtacom 3D LABAKI AMWAsci TSMTVE XMSSAT HNEIdte KPNPage SH230 Issue
Related manuals
Manual 34 pages 59.68 Kb

AVR400 specifications

The Arcam AVR400 is a high-performance AV receiver designed to provide an immersive home theater experience. As part of Arcam’s esteemed lineup, the AVR400 combines advanced technology with exceptional sound quality, catering to audiophiles and home cinema enthusiasts alike.

At the heart of the AVR400 is its impressive power amplification, providing 100 watts per channel across 7 channels, ensuring a robust performance capable of driving a wide range of speakers. This power output is complemented by a high-current design, which means the receiver can handle dynamic audio passages without distortion, offering clarity in both subtle and explosive soundtracks.

One of the standout features of the AVR400 is its support for various surround sound formats, including Dolby TrueHD and DTS-HD Master Audio. This allows for an unparalleled audio experience, transporting users right into the heart of the action. Additionally, the AVR400 is equipped with the latest HDMI inputs, ensuring compatibility with a multitude of high-definition sources, including Blu-ray players, gaming consoles, and streaming devices.

The AVR400 also boasts advanced video processing capabilities, supporting 4K pass-through as well as upscaling of lower-resolution content to 4K. This makes it an ideal choice for users looking to future-proof their home theater setup, as it can seamlessly integrate with modern 4K televisions while enhancing the quality of older content.

User-friendliness is another essential characteristic of the Arcam AVR400. It comes equipped with an intuitive on-screen menu system that simplifies the setup process. The inclusion of an automatic calibration system helps optimize speaker settings in accordance with the room acoustics, ensuring users achieve the best sound possible from their setup.

Furthermore, the network features of the AVR400 allow for streaming audio from various online services and wireless devices. Built-in support for DLNA enables users to access their media library wirelessly, while the USB input allows for direct playback from flash drives or external hard drives.

In terms of build quality, the Arcam AVR400 embodies the brand’s commitment to excellence. With a sleek design, high-quality materials, and an engineered chassis that minimizes vibration and interference, the AVR400 is not only visually appealing but also built to deliver performance over time.

In summary, the Arcam AVR400 is a feature-rich AV receiver offering a perfect blend of power, precision, and versatility. Whether for movie nights or music listening, it stands out as a reliable choice for those seeking high-quality audio and video reproduction in their home entertainment systems.