Pioneer DVH-P7050 owner manual Connecting the units

Page 88

Section

13Connecting the units

Notes

•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage.

•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.

•Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

•Secure the wiring with cable clamps or adhe- sive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short- circuiting to the vehicle body.

•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

•Do not shorten any leads. If you do, the pro- tection circuit may fail to work when it should.

•Never feed power to other equipment by cut- ting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

•When replacing fuse, be sure to use only fuse of the rating prescribed on this unit.

•Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common.

•Speakers connected to this unit must be high- power types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speak- ers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged.

•When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.

•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna.

Such connection could cause excessive cur- rent drain and malfunction.

•To avoid short-circuiting, cover the discon- nected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possibility of short-circuiting if the leads are not insulated.

•To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

88En

Page 87 Page 89
Image 88
Page 87 Page 89
Contents DVH-P7050 EnglishContents Playing Video CDs on the built-in player Playing a Video CD Playing CDs on the built-in player Playing a CDAudio Adjustments Multi-CD Player Playing a CD 45 Pausing playbackInitial Settings for DVD player Installation SpecificationsOther Functions Additional Information Compatible with DVD, Video CD and CDBefore You Start PrecautionsAbout this manual Video system of a connected component DVD disc region numbersTo ensure safe driving Region numberWhen using a display connected to Condition memoryWhat the marks on DVDs Indicate Disc operationOn CDs and Video CDs, the contents are divided Disc organizationMain features Removing the front panel Protecting your unit from theftAttaching the front panel Reverse mode About the demo modeFeature demo What’s what Head unitRemote control Remote control selection switchVolume +/- button Menu buttonJoystick ATT buttonUsing the remote control Installing the batteryUse and care of the remote con- trol Power ON/OFF When the remote control is set to DVH modeWhen the remote control is set to DVD mode Turning the unit onPress Power to turn the DVD playback off Turning the unit offTuner Listening to the radioIntroduction of advanced tuner Operation FrequenciesStoring and recalling broadcast Press F to display the function namesTuning in strong signals Storing the strongest broadcast FrequenciesPress F to select Local Press F to select BSMDVD.V indicator Playing DVDs on the built-in playerPlaying a DVD OEL displayBasic operation of DVD Press Open on the head unit to open the front panelClick the joystick Press 4or ¢Specifying chapter DVD mode Specifying title DVD modeTo perform fast forward or reverse, press and hold 1or ¡ Stopping playback Frame-by-frame playbackStill playback Slow motion playbackChanging audio language during playback Multi-audio Press Audio during playbackPress Audio while the audio selection mark is displayed Press Subtitle during playbackAbout scenes that let you change the viewing angle Changing the viewing angle during playback Multi-angleAngle mark Angle number Operating from the information display 1 DVH & DVD mode Press Display to switch the information dis- playInformation display Move the joystick left/right to select a desired optionSelecting audio, subtitle and angle Operating from the information display 2 DVH & DVD mode Selecting repeat rangeSelecting audio output Move the joystick left/right to select the audio optionPausing playback Operating from the function dis- play DVH modeRepeating play Playing Video CDs on the built-in player VCD indicatorPlaying a Video CD Insert a Video CD into the Disc loading slot Basic operation of Video CDTo skip back or forward to another track Press 4or ¢ Specifying track DVD mode Press Number buttons corresponding to a desired track numberOperating from the information Display DVH & DVD mode Press Display to switch the information dis PlayFor Time Time Search DVD mode Press Number buttons to input the desired number For TracksOperating from the function dis Play DVH mode Press F to select RPTPress eto turn repeat play off Playing CDs on the built-in player CD indicatorPlaying a CD Basic operation of CD To skip back or forward to another track, press 4or ¢Operating from the information display DVH & DVD mode Searching for a desired trackMove the joystick left/right to select Track option Track numberSetting random play Setting scan playMove the joystick left/right to select the random option Move the joystick left/right to select the scan optionPress Eto turn repeat play on Playing tracks in a random order Pausing CD playbackScanning tracks of a CD Multi-CD Player Disc multi-CD player Pausing playbackIntroduction of advanced multi- CD player operation Repeating play Playing tracks in a random orderSelect the repeat range Press Eto turn random play onPausing CD playback Using ITS playlistsScanning CDs and tracks Press F to select ScanCreating a playlist with ITS program- ming Playback from your ITS playlistUsing disc title functions Erasing a track from your ITS playlistErasing a CD from your ITS playlist Press eto erase a track from your ITS playlistEntering disc titles Using CD Text functions Displaying disc titlesSelecting discs from the disc title list Displaying titles on CD Text discsPress Eor eto select your favorite setting Using compression and bass emphasisPress F to select Comp Audio Adjustments Introduction of audio adjustmentsAudio display Press a to display the audio function namesSetting the sound focus equal- izer Using balance adjustmentAdjusting equalizer curves Using the equalizerRecalling equalizer curves Adjusting bass Fine adjusting equalizer curveAdjusting treble Adjusting loudnessUsing subwoofer output Adjusting subwoofer settingsUsing the high pass filter Using non fading outputAdjusting non fading output level Press Eor eto adjust the source vol- ume Adjusting source levelsPress a to select SLA Calling up the SET UP Menu Initial Settings for DVD playerReturning to the previous display Setting the subtitle Subtitle Lang Setting subtitles and assist subtitlesSetting the subtitle language Assist subtitlesSetting the audio language Audio Lang When you select OthersSetting the menu language Menu Lang Setting the parental lockSetting the code number and level Press Number buttons to input a four digit Code numberChanging the level When playing DVDs enabling parental lockPress Number buttons to input the regis- tered code number Setting aspect ratio TV Aspect Setting angle mark display AnglePrecautions Move the joystick up/down to select the desired TV aspectSetting for digital output PrecautionSetting digital and analog audio output Output Selection Output setting Setting detailSetting remote control code type If you forget your code numberInitial Settings Adjusting initial settingsSetting the time Setting the FM tuning stepSwitching the warning tone Setting the AM tuning stepSwitching the auxiliary setting Switching the dimmer setting Setting the rear output and subSelecting the brightness Woofer controllerSwitching the telephone muting/attenuation Switching the automatic disc playbackSetting the time display on or off Using different entertainment displaysUsing the AUX source Other FunctionsPress Eor eto select a letter of the alphabet Displaying built-in player informationPress ¡to move the cursor to the next character position Compatible with DVD, Video CD and CD Formats Additional InformationDisc types and logos Diameter/Playable sides Playback time Precautions Care of discs Language code chart for DVD Language code Input codeTroubleshooting Common problems EnglishCommon problems Problems during DVD playback Problems during Video CD playback Cause RemedyError massages on the OEL display Error messagesError massages on the display Terms of DVD/Video CD Multi-Audio Multilingual Dialog Multi-SubtitleOptical Digital Output Parental LockConnecting the units ACC position No ACC position Power cable connection Left Connection methodRight Connecting to separately sold power amp Refer to Power cable Connection onConnecting the units When connecting with a Multi-channel processor Français Italiano Nederlands When connecting the display with RCA input jack Front Video OutputWhen using a display connected to rear video output Installation DIN front/rear-mountInstallation with the rubber bush DIN front-mountRemoving the unit Remove the frame DIN rear-mountFastening the unit to the factory radio mounting bracket Specifications SpecificationsAudio GeneralInfrared Remote Control DVD playerFM tuner AM tunerPioneer Corporation
Top Page Image Contents