Kenwood KVC-1000 instruction manual Connection of Antenna Unit, Booster switch

Page 33

Connecting and Install Antenna Units

■Connection of Antenna Unit

2CAUTION

Incar antennas have a lower reception sensitivity than antennas intended for outside mounting. The picture may not appear or may be disturbed if the signal in your area is weak.

English

CAR DIVERSITY ANTENNA WITH BOOSTER CX-A330

 

OFF ON BOOST

 

 

 

 

 

To the monitor unit

 

 

 

 

Booster switch

 

 

 

 

 

ON

Set this booster switch to

 

"OFF" if there is ghosting

 

 

 

 

 

 

of the on-screen image

 

 

 

due to electromagnetic

 

OFF

fields.

 

 

 

Ignition cable (Red)ª12V

ACC

 

 

 

 

Fuse(1A)

Ground cable (Black) · (To car chassis)

■Installation for Antenna Unit

Ignition key switch

Car fuse box (Main fuse)

–+ Battery

•Attach the antenna to the inner glass surface of the rear window using double-sided tape. Carefully check the installation location as the tape can only be stuck on once.

•If the surface temperature of the glass of the rear window is low, warm it by turning on the power of the rear defogger. A cold window glass surface will weaken the adhesive strength of the double-sided tape.

Also, if installation inside the cabin is performed on a day with high humidity or when it is raining, the high humidity level will weaken the adhesive strength of the double-sided tape.

•Do not install the antenna in a location where it may obstruct the field of view during driving, such as on the windshield.

1Check the location where the antenna is to be attached. Clean off any grease or dirt from the installation location using the supplied glass cleaner, clean the area with water and allow to dry.

2CAUTION

Clean the glass thoroughly as failure to clean the glass can not only weaken the adhesive strength of the double-sided tape, but may also cause it to come loose.

2Remove the protective strips from the antenna parts and the back of the antenna unit.

3Attach the double-sided tape of the antenna parts and the antenna unit to the rear windshield glass. Attach the double-sided tape by firmly pressing down from the top. Secure cables using the supplied clampers.

4After attaching the antenna with the double-sided tape, allow it to sit undisturbed for 24 hours. Take care not to apply force to the antenna or allow it to get wet during this time.

5Wire the antenna cable to the hideaway unit.

Antenna parts

Antenna unit

Bundle cables

 

with the

Rear window

clamper bar

Accessory 8

Rear seat

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents KVC-1000 Contents DAB Control Screen Main DAB Setup ScreenDAB Control Screen Shift Disc Changer Control Screen MainMask key Safety PrecautionsMonitor Control Function Switching to the Angle/Screen Control Screen Switching the AV Output PictureSwitching to the Source Control Screen Adjusting the VolumeAngle Control Screen Screen Control Screen Menu Screen Setup Menu Screen System Setup FunctionSystem Setting Screen Clock Adjustment Screen TV Area Setting ScreenCode Security Screen When using the unit for the first timeMask Key Ending the Code Security ScreenAdjusting the Touch Position Touch Panel Adjustment ScreenRDS Setting Screen News Bulletin Function with PTY News Timeout Setting NewsAlternative Frequency Function AF Ending the RDS Setting ScreenRestricting RDS Region Region Restrict Function REG Auto TP Seek Function AtpsAudio Control Screen Audio Control FunctionTV Control Screen Main TV Control FunctionTV List Screen TV Control Screen ShiftTouch the upper centre to switch between the TV1 TV2 bands Selecting the Channels on the TV Picture ScreenAudio source control information Tuner Control Screen Main FM/AM Tuner Control FunctionTuner Control Screen Shift 3Selecting the Tuning Mode3Turning the Monaural Reception On/Off 3Turning the Local Seek Function On/OffTraffic Information Function Presetting the Volume for Traffic Information/NewsReturning to the Tuner Control Screen Main Turning TI function On/OffPTY Search Screen Cancelling the PTY Search ScreenChanging the Display Language to French or German Selecting the Type of Programme to be ReceivedDAB Setup Screen DAB Tuner Control FunctionDAB Control Screen Main Dual Channel Audio Switching Primary/Secondary Switching Selecting the Seek ModePresetting the Volume Level for Traffic Information/News DAB Control Screen ShiftDisc Changer Control Screen Main Disc Changer Control FunctionTrack Random Play Function Switching to the Disc Changer Control Screen ShiftMagazine Random Play Function Play all the tracks on the current disc in random orderDisc List Screen Disc Changer Control Screen ShiftStation Name Preset Snps /Disc Name Preset Dnps Name Set FunctionName Set Screen Remote Control Function ¢ button ButtonFM+ button AM- buttonExternal view Number of items InstallationRemoving the Hard Rubber Frame Audio/Visual Input or Output IN-OUT settingKVC-1000 KTC-1000R/A907Connection of Antenna Unit Booster switchProblem Possible Cause Solution Troubleshooting GuideEject Monitor Section Specifications
Top Page Image Contents