Operating Instructions

[RESET] Button

VM9511TS

Power On / Off

Press the /MUTE button (7) to turn the unit on. The buttons on the front of the unit light up and “WELCOME” appears briefly in the LCD panel (23), followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen.

Press and hold the /MUTE button (7) on the front panel or the POWER button (4) on the remote to power off the unit.The monitor is drawn back into the main compartment and the LCD screen displays “BYE BYE”.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The beep tone cannot be disabled.

Mute

Press the /MUTE button (7) on the front panel or the MUTE button

(3)on the remote to mute the volume from the unit. Press the MUTE button again to restore the volume. “MUTE” is displayed on the LCD monitor. Adjusting the volume or using any of the audio setup features cancels the mute function.

Playing Source Selection

Press the SRC button (15) on the front panel or the SRC button (8) on the remote to change between available playing sources in the following order: TUNER, DVD, CD Changer, AUX IN, CAMERA (rear view video camera) and SD. The playing mode is displayed on the TFT and LCD screens.

AUX IN Mode

An external peripheral device can be connected to this unit via RCA output and “AUX-IN”.

CAMERA Mode

“CAMERA” mode is only available if the camera is connected and during reverse driving. To install a rear view video camera, connect the video input cable to the camera output cable.

Volume Adjustment

To increase or decrease the volume level, turn the ROTARY ENCODER (6) on the front panel or press the VOL+/ VOL- buttons (15, 16) on remote control. When the volume level reaches “0” or “40”, a beep sounds, indicating that the adjustment limit has been reached. The volume ranges from “0” to “40”. The LCD or TFT screen displays the volume level for 3 seconds.

To program a specific volume level, push and hold the VOL/ LO/DX knob (6) while the yellow volume bar is displayed on the screen. The unit will beep two times to confirm your turn- on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. To get the best possible sound quality from your new system, be sure to adjust the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the VOL/LO/DX knob (6) on the front panel once to display the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Continuously press the VOL/LO/DX knob (6) on the front panel, or press the (>>)/(<<) buttons (14, 22) on the remote control or the (/\)/ (V) buttons (18, 19) on the joystick to select the audio feature to be adjusted.

Adjusting an Audio Feature

Rotate the VOL/LO/DX knob (6), press the (<<)/(>>) buttons (17,

19)on the remote control, or press the (<)/(>) buttons (16, 17) on the joystick to adjust the selected feature to the desired setting.

Table 5: Audio Adjustments

Audio Function	Adjustable Range


EQ	User
	Flat

	Jazz

	Pop
	Classical

	Rock

	Vocal
BASS	-14 to +14

TREBL	-14 to +14

SUB	-7 to +7
LOUD	0 (off), 1-4

FAD (Fade)	-9 to +9

BAL	-9 to +9

The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or “off”. When the Loud function is on, “LOUD” is displayed on the screen.

Exiting the Audio Control Menu

Press and hold the VOL/LO/DX knob (6) or stop making adjustments for a few seconds to exit the audio control menu.

Six-Channel Audio Control

NOTE: Before adjusting the volume of any speaker, please refer to “Surround Sound” on page 26.

Table 6: 6-Channel Audio Adjustments

Item	Adjustable Range


Master Volume	00 to 40

Front Left Channel Volume	-10 to +10

Front Right Channel Volume	-10 to +10

Rear Left Channel Volume	-10 to +10

Rear Right Channel Volume	-10 to +10

Center Channel Volume	-10 to +10

Subwoofer Volume	-10 to +10

Rear Zone

If a monitor is installed in the rear zone and connected to the rear zone AV output, passengers in the back seat can control the DVD output using the rear zone remote control. See “Multi-Zone Remote Control” on page 12 for instructions.

System Reset

To correct a system halt or other illegal operation, use the tip of a pen to press the RESET button (22) located on the front

bottom-right corner of the unit. After a system reset, the unit restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a

Programmable Turn-On Volume	NOTE: The Bass and Treble levels are only adjustable
This feature allows the user to select a turn-on volume setting	when EQ is set to “User” mode.

regardless of the volume setting prior to turning the unit off.

telephone call is received by the car phone or when verbal navigation is performed.

VM9511TS specifications

The Jensen VM9511TS is a cutting-edge multimedia receiver designed to enhance the in-car entertainment experience while keeping the focus on safety and functionality. One of its standout features is the 6.8-inch touchscreen display, which enables users to easily navigate through different functionalities. The screen boasts a high resolution, ensuring that videos and images are crisp and clear, allowing for an enjoyable viewing experience.

One of the main attractions of the Jensen VM9511TS is its compatibility with various media formats. The receiver supports DVDs, CDs, and a range of digital formats, meaning users can enjoy their favorite content from a variety of sources. The built-in Bluetooth connectivity is another significant feature, enabling hands-free calling and audio streaming from smartphones. This not only enhances convenience but also contributes to safer driving by allowing users to keep their hands on the wheel.

Additionally, the VM9511TS features USB and AUX inputs, providing further options for connecting external devices. Whether it's a flash drive loaded with music or a smartphone through an auxiliary cable, users can easily play their preferred media. The receiver also supports video playback through its rear-view camera input, making it an excellent choice for those looking to enhance their vehicle's safety features.

Audio quality is a key focus of the Jensen VM9511TS, which is equipped with a built-in amplifier. The unit ensures that sound is delivered with clarity and power. It also offers customizable audio settings, allowing users to adjust bass, treble, and balance to suit their preferences. The equalizer settings available provide a tailor-made listening experience, enhancing the enjoyment of any type of music.

Moreover, the Jensen VM9511TS is designed with user-friendliness in mind. Its intuitive interface simplifies navigation, and the responsive touchscreen allows for quick access to functions. The receiver also supports steering wheel controls, allowing users to keep their attention on the road while adjusting settings.

In summary, the Jensen VM9511TS is a versatile multimedia receiver that combines functionality with modern technology. Its range of features, from touchscreen navigation to audio customization, makes it a top choice for those seeking to upgrade their car's entertainment system while ensuring a safe driving environment. With its robust capabilities and user-centric design, the Jensen VM9511TS stands out in the competitive landscape of in-car receivers.