Tascam MD-301mkII user service Display Messages

Page 20

Track combination may not be possible. Tracks created by other editing operations sometimes cannot be combined.

Audio is interrupted during search. When a track created by an editing operation is searched, audio is some- times interrupted.

Track numbers are not assigned correctly.

When a CD is recorded through a digital connection, short tracks may be recorded depending on the contents of the CD. Also, when auto track marking is performed, the track numbers may not be assigned correctly in some cases.

The "TOC Reading" display will not disappear.

"TOC Reading" is displayed for a longer time than usual when a brand-new recordable MD is inserted.

Note the following when you attempt to perform recording while erasing (overwriting) the previous recording:

The remaining recording time of the MD may not be displayed correctly.

After repeated overwrite operations, it may no longer be possible to overwrite recording. In this case, first edit the previous recording (by erasing tracks, etc.) then proceed to the overwrite operation.

The remaining recording time is shorter after recording than it was before recording.

The overwrite operation is not recommended if the track to be overwritten contains noise. Since recording is performed on a 6-cluster basis (approx. 12 seconds), over- writing a noisy track may erase a part of the track.

It is not possible to assign a track title during overwrite recording.

Sometimes the maximum recording time (60 or 74 minutes) will not be available even after performing "ERASE DISC".

In this case, try performing "ERASE DISC" again. However, you will not be able to UNDO it afterwards.

Display Messages

The following messages are displayed depending on the operation conditions.

Message

Description

 

 

Blank Disc

The recordable MD contains no recorded data.

 

 

Cannot Copy !

Copying is not possible.

 

 

Cannot EDIT !

Editing is not possible.

 

 

Disc Error !

The data in the MD is abnormal.

 

 

Disc Full !!

No more recording is possible.

 

 

D-IN UNLOCK !

Digital input connection is not made.

 

 

ERASE DISC ?

Is it OK to erase the recorded data on the MD ?

 

 

ERASE TRK ?

Is it OK to erase this track ?

 

 

Name Full !!

The title memory is full.

 

 

NO DISC !!

No MD is inserted.

 

 

No Track !!

No track has been recorded.

 

 

PGM Empty !!

Tracks have not been programmed.

 

 

PGM Full !!

No more tracks can be programmed.

 

 

Play Mode !!

The selected play mode is inappropriate.

 

 

Protected !!

The MD is protected against accidental erasure.

 

A playback-only MD is loaded.

 

 

Rec Error !!

A recording error occurred.

 

 

Track Full !!

The MD has used up all its track numbers.

 

 

UNDO ?

Is it OK to cancel the last operation ?

 

 

UTOC Writing

The recorded data is being written on the MD.

 

 

– 20 –

Image 20
Contents MD-301@# Important Safety Instructions Label required in this reguration is shown Optical pickup Type KMS-260AManufacturer Laser output 55 mW Wavelength 785 ±20 nmContents Before UseWhen Protected !! is displayed When D-IN Unlock ! blinksRemote Control Unit Handling MDsConnections Rack MountingVoltage Conversion ConnectionName of Each Control ªSTOP button p ¥PLAY button a πREADY buttonNumeric buttons 1 to 9, 0, +10 g REPEAT/A-B buttons Sync Record button Upper/Lower case button Aß∑aRecording Recording an MDTo protect an MD against accidental erasure Display Selected InputHeadphones PlaybackNormal Playback To play a track located before or after Current trackMonitoring the Input Signal Adjusting the Recording LevelUseful Tips for Recording Assigning Track Numbers During RecordingTimer Recording Sync RecordingChecking the Remaining MD Recording Time Checking the Recorded TracksUsing the Display Window Useful Tips for PlaybackSelecting the Desired Track Playing Tracks in Random Order Shuffle PlaybackWhen Recording to Analog Tape Timer Playback Repeating Tracks Repeat PlaybackEditing Recorded MDs Erasing Tracks Erase FunctionCombining Tracks Combine Function Moving a Track Move FunctionExample Combining B and C Example To move D from track number 4 to track numberAssigning Titles Title Function Press the Display button to select the character typeChanging entered characters Copying a Title Title Copy FunctionTitle entry keys Optional Functions System RestrictionsªEditing keys Display Messages … Rule Guide to the Serial Copy Management SystemSerial Copy Management System TOC TroubleshootingSpecifications To the User