Advantech IPPC-9151 Series user manual Safety Instructions

Page 6

Safety Instructions

1.Read these safety instructions carefully.

2.Keep this User's Manual for later reference.

3.Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.

4.For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.

5.Keep this equipment away from humidity.

6.Put this equipment on a reliable surface during installation. Dropping it or let- ting it fall may cause damage.

7.The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.

8.Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

9.Position the power cord so that people cannot step on it. Do not place anything over the power cord.

10.All cautions and warnings on the equipment should be noted.

11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12.Never pour any liquid into an opening. This may cause fire or electrical shock.

13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14.If one of the following situations arises, get the equipment checked by service personnel:

a.The power cord or plug is damaged.

b.Liquid has penetrated into the equipment.

c.The equipment has been exposed to moisture.

d.The equipment does not work well, or you cannot get it to work according to the user's manual.

e.The equipment has been dropped and damaged.

f.The equipment has obvious signs of breakage.

15.DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16.CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-

TIONS.

The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan- tech disclaims all responsibility for the accuracy of any statements contained herein.

IPPC-9151 Series Users Manual

vi

Image 6
Contents IPPC-9151 Series Copyright notice Acknowledgments FCC Class a Packing List Thermal GreaseIPPC-9151F-XAE Additional Information and AssistanceSafety Instructions Wichtige Sicherheishinweise Viii Contents Chapter Audio Setup Chapter Award Bios Setup IR connector CN24 102 General Information Sturdy structure Easy maintenanceIntroduction EconomicalSpecifications GeneralStandard PC Functions AGP SVGA/Flat Panel Interface Audio FunctionPcmcia interface Optional AccessoriesPCI bus Ethernet Interface Analog Resistive Touchscreen optionalDimensions IPPC-9151FA DimensionsSystem Setup Quick Tour of IPPC-9151 Side View 1 PS/2 Mouse and Keyboard Parallel PortVGA port Serial COM ports USB portsAudio Interface Adjusting the LCD brightness EthernetSystem turn ON/OFF Installing Sdram Sdram Installing a CPU Ics personnel should open the panel PCInstalling a 3.5 HDD Insert the FDD, CD-ROM Module and fix the back cover Panel Mounting Installing Add-on CardsMounting Instructions Rack MountingJumper Settings and Connectors Jumper Settings Connectors Jumpers and ConnectorsSetting jumpers Jumpers and switches Jumper LocationsConnectors Panel PC connectorsLocating connectors Connectors on IPPC-9151 motherboardCPU Installation Cmos Clear for External RTC JP31 COM2 RS-232/422/485 setting JP4 COM-port interface JP4, JP5LCD panel power setting VGA interfaceIntel Chipset Driver Installation Installation for Windows 98/NT/ME/2000/XP Further Information PCI Bus Ethernet Inter- face Installation of Ethernet Driver PCI Bus Ethernet InterfaceInstallation for Windows 98/NT/ME/2000 Click Next Click Install Click Finish Page VGA Setup Chipset Display memoryDisplay types Installation of the VGA Driver Installation for Windows 95/98/MEFurther Information Audio Setup Installation of the Audio Driver Installation for Windows 98/ME/2000/XP Page Touchscreen Touchscreen Specifications Sensor board Installing Driver for Windows 2000/XPEnvironmental Specifications Ball drop testSETUP.EXE DMC9000.inf DMC9000.sys DMC9000.catAppendix8 Page Appendix8 Configuring PenMount Windows 2000/XP Driver PenMount Control PanelCalibrate Older the touch screen, the more Page Appendix8 Draw Multiple Monitors Page Appendix8 Option About PenMount Monitor Menu Icon Configuring the Rotate Function PenMount Rotating FunctionsUninstall the PenMount Windows 2000/XP driver Pcmcia Installation of Pcmcia Driver PcmciaInstallation for Windows Page Award Bios Setup Award Bios Setup Cmos Setup UtilityStandard Cmos Setup Standard Cmos featuresDate mmddyy Time hhmmssPrimary / Secondary & Master / Slave Halt On Drive a / Drive BVideo Select Display DeviceExtended Memory Advanced Bios FeaturesBase Memory Total MemoryVirus Warning CdromFirst/Second/Third/Other Boot Device Processor Number FeatureQuick Power On Self Test Boot Up Floppy SeekReports No FDD For Win95 Video Bios Shadow Typematic Rate SettingTypematic Delay Msec Gate A20 OptionSmall Logo EPA show Advanced Chipset FeaturesC8000-CBFFF to DC000-DFFFF Shadow Dram Timing by SPDDram Clock System Bios CacheableAGP- 4X Mode Sdram Cycle LengthAGP Driving Value Boot Device SelectAGP Driving Control OnChip USBIntegrated Peripherals IDE Prefetch Mode OnChip IDE Channel 0/1Primary Master / Slave PIO & Secondary Master / Slave PIO IDE HDD Block ModeUart 2 Mode Primary Master / Slave Udma & Secondary Master / Slave UdmaECP Mode Use DMA TX, RX inverting enableOnboard Paralle Mode IR Function DuplexPower Management Setup Power ManagementAcpi Function PM Control by APM Video Off OptionVideo Off Method Modem Use IRQSoft-Off by Pwrbtn Page Reset Configuration Data 10.7 PnP/PCI ConfigurationPNP OS Installed Resource Controlled ByPCI/VGA Palette Snoop IRQ ResourcesDMA Resources Assign IRQ for VGACurrent CPU FAN2 Speed PC Health StatusCurrent CPU FAN1 Speed Vcore/2.5V/3.3V/5V/1.2VFrequency/Voltage Control Load Optimized DefaultsLoad Optimized Defaults Y/N ? N Auto Detect DIMM/PCI CLKSet Password Save to Cmos and Exit Y/N ? Y Save & Exit SetupExit Without Saving Quit Without Saving Y/N ? NLCD Specifications and Selection Settings Appendix a LCD Specifications IPPC-9120G/9150G/9151 Series LCD SpecificationsPin Assignments ATX Power connector 1 CN1 Appendix B Pin AssignmentsATX power connector 2 CN2 Lvds connector 1CN4Lvds connector 2CN6 Inverter power connector CN5FDD connector CN9 Table B.6 FDD connector CN9Internal speaker connector CN15 IR connector CN24Fan power connector FAN1 & FAN2