Blaupunkt RCM 169 Switching the equalizer on/off, Self-adjusting equalizer, Hi-fi self-adjustment

Page 38
To start the hi-fiself-adjustment, activate the DSA menu.
To take the reading hold the microphone in the corresponding position.
For EQ1 (driver alone), hold the microphone directly where the driver’s head would be. For EQ2 (driver and front-seat passenger), hold the microphone between the driver and front passenger seat and for EQ3, hold the microphone directly in the centre of the ve- hicle (left/right, front/rear).
These readings must be taken in a quiet area. Outside noise will distort the results. Make sure that nothing impedes the sound being emitted from the speakers. The mi- crophone must be connected to the car ster- eo system.

DSA – Digital Sound Adjustment

refer to the section on “Self-adjusting equal- EQ 3

for passengers in the front and

izer” or “Manual equalizer adjustment”.

back

The settings for “Rock to Vocal” are fixed values which cannot be adjusted.

• Press / to select the desired set- ting.

Switching the equalizer on/off

• To switch the equalizer off, press <<. “EQ off” will appear in the top line of the dis- play.

• To switch the equalizer on, press >>.

Self-adjusting equalizer

(Hi-fi self-adjustment)

This car stereo is equipped with a self-ad-

justing, adaptive 7-band equalizer for two

Starting the hi-fi self-adjustment

The car stereo system must be switched on.

channels.

The left and the right channel can be ad-

• Place the microphone as required for

justed electronically for each equalizer set-

the setting you want to store.

ting.

The reading will not be correct if the micro-

 

phone is held in the wrong position.

•Press / to select the setting you want to alter (EQ1, EQ2, EQ3).

To start the self-adjustment

•press ADJ and AUTO one after the other.

“MicPos5” will appear in the top line of the display, the countdown will begin. Following the countdown, the fully automat- ic self-adjustment will begin.

Hi-fi self-adjustment

You can take electronic readings and store them for three different situations, e.g.: EQ 1 for the driver alone

EQ 2 for the driver and a front-seat pas- senger

•Press DSA and EQ one after the other.

The setting selected last will appear in the top line of the display.

Noise which gradually increases in volume will be emitted from the speakers; the top line of the display will flash at the same time. Make sure that your surroundings are as quiet as possible while the reading is being taken.

86

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Atlanta RCM Erklärung der Positions-Nummern siehe Kurzanleitung Contents Contents Quick Reference Next AM MW, LW Quick ReferenceNext FM FM, TS, TA, AM, PS, Scan Menu level Adjusting the radio functionsPRE ExitRT Radio text PTYREG Regional MonoMIX CLR Rocker switchRadio station seek tuning NameAUD DIS= CDC DisplayDOT field @ Cassette slot KeyCard theft protection system Eject? TU tuner Visual theft protectionRC 08 remote control unit Important notes Removing the KeyCard KeyCard theft protection systemOperating the unit for the first time Incorrect KeyCardKeyCard theft protection system Care of your KeyCard Training the new KeyCard Switching off the flashing lightLost or damaged KeyCard Closing the Install menu First-time installationActivating the Install menu Setting the clockConnecting external equipment First-time installationSwitching the ignition connec- tion on/off Reset to default settingsSelecting the operating Optimising the viewing Mode Angle AF Alternative frequency Switching between the menu levelsRadio operation with RDS Radio Data System Radio operation with RDS Radio Data System Station tuningAutomatic tuning REG regional programStoring stations Scrolling through the broadcast- ing networks FM onlyChanging the memory bank FM Scanning stored stations with Preset ScanTo start Preset Scan Recalling stored stationsScanning stations with Radio Scan Selecting the seek tuning sensi Automatic bandwidth adjustSwitching from stereo to mono TivityNews Switching PTY on/offProgram type Selecting and storing PTY program typesTo select any program type PTY seek tuningRadio text Storing program typesTraffic information station reception with RDS-EON Switching radio text offSwitching the warning beep off Activating radio textTape operation Automatic seek tuning startSwitching on tape deck opera- tion Inserting a cassetteTrack reverse Selecting the display modeTape operation Scanning cassette titles withCare instructions Repeating titles with RPTFast tape forward/rewind Fast forward Fast rewindSwitching on CD changer operation CD changer operationRepeating tracks/CDs CD changer operationSelecting tracks Entering CD names Deleting CD names/TPM at the same timeDisplaying the clock Clock display when the audio system is switched offCD changer operation Clock Time AutomaticallySynchronisation Selecting a 12 or 24-hour modeActivating the equalizer settings Hi-fi self-adjustment Switching the equalizer on/offSelf-adjusting equalizer Starting the hi-fi self-adjustmentAltering the setting manually Activating an equalizer settingManual equalizer adjustment JazzSwitching DNC on/off Adjusting DNCAdjusting DNC sensitivity Safety informationDSC programming TUN TunerDSC programming VAR VariousTOM ReadScan Scantime Sync CLK ClockSET Overview of the DSC default settings CDC changerTuner Specifications Glossary Technical TerminologyAmplifier Tape deckGlossary Technical Terminology REGGlossary Technical Terminology RDS-EON IndexCPS TPMBosch Gruppe Service-NummernUSA
Related manuals
Manual 44 pages 22.7 Kb
Top Page Image Contents