JVC GET0195-001A Avant de commencer la connexion Vérifiez, Alvorens de verbindingen tot stand te

Page 43

ENGLISH

DEUTSCH

FRANÇAIS

NEDERLANDS

A Typical Connections / Typische Anschlüsse / Raccordements typiques / Normale verbindingen

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.

The leads of the power cord and those of the connector from the car body may be different in color.

1Connect the colored leads of the power cord in the order specified in the illustration below.

2Connect the aerial cord.

3Finally connect the wiring harness to the unit. Note: If your vehicle does not have any accessory terminal, move the fuse from the fuse position 1 (initial position) to fuse position 2, and connect the red lead (A7) to the positive

(+) battery terminal.

• The yellow lead (A4) is not used in this case.

Vor dem Anschließen: Die Verdrahtung im Fahrzeug sorgfältig überprüfen. Falsche Anschlüsse können ernsthafte Schäden am Gerät hervorrufen.

Die Leiter des Stromkabels und die Leiter des Anschlusses im Fahrzeug können sich farblich unterscheiden.

1Die farbigen Adern des Stromkabels in der Reihenfolge anschließen, wie in der Abbildung unten gezeigt.

2Das Antennenkabel anschließen.

3Die Kabelbäume am Gerät anschließen. Hinweis: Verfügt Ihr Fahrzeug nicht über eine Zubehöranschlußklemme, die Sicherung von der 1. Sicherungsposition (Erstposition) in die 2. Sicherungsposition versetzen, die rote Leitung (A7) an der (+) Batterieanschlußklemme anschließen.

• Die gelbe Leitung (A4) wird in diesem Fall nicht verwendet.

Avant de commencer la connexion: Vérifiez

attentivement le câblage du véhicule. Une connexion incorrecte peut endommager sérieusement l’appareil.

Le fil du cordon d’alimentation et ceux des connecteurs du châssis de la voiture peuvent être différents en couleur.

1Connectez les fils colorés du cordon d’alimentation dans l’ordre spécifié sur l’illustration ci-dessous.

2Connectez le cordon d’antenne.

3Finalement, connectez le faisceau de fils à l’appareil.

Remarque: Si votre véhicule ne possède pas de borne accessoire, déplacez le fusible de la position de fusible 1 (position originale) à la position de fusible 2 et connectez le fil rouge (A7) à la borne positive (+) de la batterie.

Le fil jaune (A4) n’est pas utilisé dans ce cas.

Alvorens de verbindingen tot stand te

brengen: Moet u de bedrading in de auto zorgvuldig. Het apparaat kan door verkeerde verbindingen ernstige schade oplopen.

De draden van het stroomsnoer verschillen mogelijk van kleur metde aansluitingen op het chassis van de auto.

1Verbind de gekleurde draden van het stroomsnoer in de afbeelding hieronder aangegeven volgorde.

2Sluit de antenne aan.

3Verbind de draadbundel daarna met het apparaat. Opmerking: Als uw voertuig niet beschikt over een aansluitklem, moet u de zekering verplaatsen van stand 1 (beginstand) naar stand 2 en moet u de rode draad (A7) met de pluspool (+) van de accu verbinden.

In dit geval wordt de gele draad (A4) niet gebruikt.

Line out (see diagram

 

 

)

To steering wheel remote controller (see diagram

 

)

 

 

 

An Lenkradfernbedienung (siehe Schaltplan

 

 

)

 

 

 

 

Schutz kappen Signalausgang

 

 

 

 

 

 

Pour la télécommande de volant (voir le diagramme

 

 

)

(siehe Schaltplan

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

Naar stuurwiel-afstandsbediening (zie schema

 

)

 

 

 

 

 

 

Sortie de ligne

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(voir le diagramme

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Uitgang (zie schema

)

 

 

 

 

Rear ground terminal

 

 

 

 

 

Hintere Erdungscan–

B1

B3

B5

B7

 

schlußklemme

B2

B4

B6

B8

 

Borne arrière de masse

 

 

A5

A7

15

A2

A4

 

A8

 

Massaklem aan de achterkant

 

 

 

 

 

 

Black

 

 

 

Schwarz

 

 

 

Noir

A8

Aerial terminal

 

Zwart

 

3

 

Antennenanschlußklemme

2

 

Borne de l’antenne

 

Aansluitpunt antenne

 

 

 

 

 

 

B1

B3

B5

B7

 

 

 

Fuse position 2 / 2. Sicherungsposition / Position de fusible 2 / Zekering, stand 2

 

 

 

B2

B4

B6

B8

 

 

 

 

 

 

 

 

A5

A7

 

 

 

Fuse position 1 / 1. Sicherungsposition /Position de fusible 1 / Zekering, stand 1

 

 

 

A2

A4

 

A8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15 A fuse

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

15 A Sicherung

 

 

 

 

 

 

 

 

 

 

 

Fusible 15 A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zekering 15 A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*1

Not included for this unit

 

 

 

 

 

 

 

 

 

 

 

 

 

*1

Wird nicht mit Gerät mitgeliefert

Ignition switch

 

 

 

 

 

 

 

 

*1

Non fourni avec cet appareil

 

 

 

 

Zündschalter

 

 

 

 

 

 

 

 

*1

Niet bij het apparaat inbegrepen

 

 

 

 

Interrupteur d’allumage

 

 

 

To metallic body or chassis of the car

 

 

 

 

*1

 

Ontstekingsschakelaar

 

 

 

 

 

 

 

 

 

 

 

 

Zur metallenen Karosserie oder zum Fahrwerk des Autos

 

 

 

 

 

 

 

 

 

 

1 Vers corps métallique ou châssis de la voiture

 

 

 

 

*1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Naar metalen ondergrond of chassis van de auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yellow*2

Gelb*2

Jaune *2

Geel *2

Red

Rot

Rouge

Rood

 

To a live terminal in the fuse block connecting to the car battery

 

(bypassing the ignition switch) (constant 12 V)

 

Zur einer stromführenden Anschlußklemme im Sicherungsblock zum

A4

Anschließen an die Autobatterie (Umgehen des Zündschalters)

(konstant 12 V)

2À une borne sous tension du porte-fusible connectée à la batterie de la voiture (en dérivant l’interrupteur d’allumage) (12 V constant)

Naar een onder spanning staande aansluitklem in het zekeringblok die is aangesloten op de accu van de auto (u passeert de ontstekingsschakelaar) (constant 12 V)

A7

To an accessory terminal in the fuse block

Zur einer Zubehöranschlußklemme im Sicherungsblock

3

Vers borne accessoire du porte-fusible

Naar een aansluitklem in het zekeringblok

Fuse block Sicherungsblock Porte-fusible

Zekeringblok

*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

*2 Vor der Überprüfung der Funktionsfähigkeit des Geräts vor dem Einbau, muß diese Leitung angeschlossen werden, da sonst die Stromversorgung nicht eingeschaltet werden kann.

*2 Pour vérifier le fonctionnement de cet appareil avant installation, ce fil doit être raccordé, sinon l’appareil ne peut pas être mis sous tension.

*2 Voordat u controleert of het apparaat werkt (alvorens het te

D

installeren), moet deze draad aangesloten zijn. Als dit niet het geval is, kan de stroom niet worden ingeschakeld.

Blue with white stripe

Blau mit weißem Streifen

Bleu avec bande blanche

Blauw met witte streep

Brown

Braun

Marron

Bruin

 

To the remote lead of other equipment or power aerial if any (200 mA max.)

A5

Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern vorhanden

 

4Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une

(200 mA max.)

Naar afstandsdraad van andere apparatuur of antenne met circuit indien aanwezig (200 mA max.)(max. 200 mA)

A2

To cellular phone system

Zur Mobiltelefon

5

À un système de téléphone cellulaire

Naar het mobiele-telefoonsysteem

6

B6

B5

 

B4

B3

 

B8

B7

 

B2

B1

White with black stripe

 

White

Gray with black stripe

 

Gray

Green with black stripe

 

Green

Purple with black stripe

Purple

Weiß mit schwarzem

 

Weiß

Grau mit schwarzem

 

Grau

Grün mit schwarzem

 

Grün

Lila mit schwarzem

Lila

Streifen

 

Blanc

Streifen

 

Gris

Streifen

 

Vert

Streifen

Violet

Blanc avec bande noire

 

Wit

Gris avec bande noire

 

Grijs

Vert avec bande noire

 

Groen

Violet avec bande noire

Paars

Wit met zwarte streep

 

 

Grijs met zwarte streep

 

 

Groen met zwarte streep

 

 

Paars met zwarte streep

 

Left speaker (front)

Right speaker (front)

Left speaker (rear)

Right speaker (rear)

Linker Lautsprecher (vorne)

Rechter Lautsprecher (vorne)

Linker Lautsprecher (hinten)

Rechter Lautsprecher (hinten)

Enceinte gauche (avant)

Enceinte droit (avant)

Enceinte gauche (arrière)

Enceinte droit (arrière)

Linkerspeaker (voorin)

Rechterspeaker (voorin)

Linkerspeaker (achterin)

Rechterspeaker (achterin)

 

3

 

 

Image 43
Contents KD-G401 How to use the Mode button How to reset your unitContents Control panel Location of the ButtonsDisplay window Basic Operations Turning on the powerTo drop the volume in a moment To turn off the powerSame procedure and select Demo on in step Finish the settingTo cancel the display demonstration, follow Procedure belowSetting the clock Select the band FM1 3, AM Radio OperationsListening to the radio Searching for a station automatically Auto searchEach time you press Button, the band changes as Follows When an FM stereo broadcast is hard to receiveSearching for a station manually Manual search FM1 FM2 FM3 AMSelect the FM band FM1 3 you want to store FM stations into FM station automatic preset SSMManual preset Storing stations in memoryPreset number flashes for a while Tuning in to a preset stationWhat you can do with RDS RDS OperationsTo use Network-Tracking Reception To deactivate the TA Standby Reception Using TA Standby ReceptionPress TP PTY again. The TP indicator Disappears Press TP PTY to activate TA Standby ReceptionTo deactivate the PTY Standby Reception Using PTY Standby ReceptionPress and hold the number button PTY code selected into the preset Number you wantSearching your favorite programme To store your favorite programme typesPress ¢ or 4to start PTY search for your favorite programme Ex. When Rock M is selectedTurning the control dial clockwise Setting the TA volume levelAutomatic clock adjustment To activate programme search, follow the procedure belowSame programme can be received on different frequencies PTY codesInsert a CD into the loading slot CD OperationsPlaying a CD To stop play and eject the CDTo go to a particular track directly How to use the +10 and -10 buttonsTo fast-forward or reverse the track To go to the next or previous tracksTo play back tracks repeatedly Track Repeat Play To play back tracks at random Disc Random PlayDisc title / performer Track title To cancel the prohibition and unlock the discPlaying a CD Text Prohibiting disc ejection While pressing CD, press and hold 0 for more than 2 secondsHierarchy Level What is MP3?MP3 Introduction Compatible with ID3 TagInsert an MP3 disc into the loading slot MP3 OperationsPlaying an MP3 disc To stop play and eject the discTo fast-forward or reverse the file To change the display informationTo skip to the next or previous files To select a particular file in a folder, press Current folder +10 and -10 buttonsTo go to a particular folder directly To go to a particular file quickly withinTo skip to the next or previous folder CanceledTo play back files at random Folder Random/Disc Random Play Indication For Preset values Sound AdjustmentsRepeat steps 1 and 2 to adjust the other items Adjusting the soundSelect the item you want to adjust Adjust the settingEx. When you select Dimmer Changing the general settings PSMBasic Procedure Adjust the PSM item selected24H/12H Preferred Setting Mode PSM itemsIndications Selectable values/items SeeTo turn the tag display on or off To select the dimmer mode-DIMMERTo select the telephone muting-TEL To select the scroll mode-SCROLLDetaching the control panel ConnectorsAttaching the control panel Installing the battery Using the Remote ControllerRM-RK60 Location of the buttonsSymptoms Causes Remedies TroubleshootingStored in memory are erased About mistracking Handling discs MaintenanceLW Tuner SpecificationsFM Tuner MW Tuner Having Trouble with operation? Und Erdung ausgelegt. Verfügt Ihr Fuse blows HinweisRemarque HinweiseAlvorens de verbindingen tot stand te Avant de commencer la connexion VérifiezRear ground terminal Hintere Erdungscan Schlußklemme KD-G401 Rear speakersFront speakers Vordere Lautsprecher