Kenwood DPX-MP2090U Accessories/ Installation Procedure, Accessories Installation Procedure

Page 34

Accessories/ Installation Procedure

Accessories

1

..........1

2

..........1

3

..........6

4

..........6

5

..........1

Installation Procedure

1.To prevent a short circuit, remove the key from the ignition and disconnect the - battery.

2.Make the proper input and output wire connections for each unit.

3.Connect the speaker wires of the wiring harness.

4.Connect the wiring harness wires in the following order: ground, battery, ignition.

5.Connect the wiring harness connector to the unit.

6.Install the unit in your car.

7.Reconnect the - battery.

8.Press the reset button.

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

•If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.

•If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

•If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.

•If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.

•Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

•Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.

•When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal.

•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

•Mount the unit so that the mounting angle is 30° or less.

34 English

Page 33 Page 35
Image 34
Page 33 Page 35
Contents DPX-MP2090U Contents Do Not Load 8 cm 3 in. CDs in the CD slot Safety precautionsTo prevent injury or fire, take the following precautions Lens FoggingHow to reset your unit Cleaning the UnitAbout DAB Tuner control Marking of products using lasers Except for some areasAutomatic Switching DAB priority Auto Ensemble Memory EntryAbout CDs About the Connection of the USB device About USB deviceAvailable USB devices About USB device OperationAbout AAC, MP3 and WMA Playing order of the Audio file Volume General featuresPower Selecting the SourceSystem Q Sound setting DisplaySelect the Basic Audio item to adjust Press the VOL knob Audio ControlAdjusting the detail of Audio Control Audio SetupSubwoofer Output Speaker SettingTEL Mute CD & External disc source Switching DisplayTuner source Audio file sourceTuning Tuner/TV control featuresTuning Mode Preset Tuning Direct Access TuningStation Preset Memory Frequency Step SettingPreset TV Tuning TV TuningTV channel Preset Memory Direct TV TuningPlaying CD & Audio file CD/USB device/Audio file/External disc control featuresPlaying USB device Track/File Search Playing External DiscFast Forwarding and Reversing Disc Search/Folder SearchTrack/File/Disc/Folder Repeat Direct Track/File SearchDirect Disc Search Scan PlayMagazine Random Play Select modeCancelling the All Random Play All Random PlaySelect the file Push the Control knob towards 4 or ¢ File Select modeFolder Select 1 mode Folder name display Displays the current folder nameSwitching the Play mode Folder Select 2 modeCheck the name of upper level folder Text/Title Scroll Cancelling the Letter SeekLetter Seek Selected initial group playsMenu system You can continue by returning to and setting other itemsExit Menu mode Press the Menu button Select the Beep displayApproved is displayed Security Code function activates Activating Security CodeDeactivating Security Code To deactivate the Security Code functionTouch Sensor Tone Manual Clock AdjustmentSwitching preout Indirect LightingCrsc Clean Reception System Circuit Built-in Amp SettingDual Zone System Setting S. Bass Management SystemCD Read Setting Auxiliary Input Display SettingBuilt-in Auxiliary input Setting Text ScrollVoice Index Audio Preset MemorySetup Sound Control ACDrive firmware version displayAudio Preset Recall Recalling the sound setup registered by Audio Preset MemoryLoading and Replacing the battery Basic Operations of remote controlBasic operations Disc/USB source Dual Zone SystemTuner source TV sourceAccessories/ Installation Procedure Accessories Installation ProcedureConnecting Wires to Terminals Installation InstallationUSB Device Connection Troubleshooting Guide GeneralTuner source Disc sourceUSB device source Audio file sourceMessages shown below display your systems condition Load Specifications Page

DPX-MP2090U specifications

The Kenwood DPX-MP2090U is a versatile and feature-rich car stereo designed to enhance your in-car audio experience. This model stands out for its blend of modern technology, user-friendly interface, and excellent sound quality, making it a popular choice among car audio enthusiasts.

One of the key features of the Kenwood DPX-MP2090U is its ability to play a variety of media formats. The stereo supports CD, MP3, WMA, and WAV playback, ensuring that all your favorite music formats can be enjoyed on the go. Additionally, it comes equipped with a USB port, which allows for effortless connection of USB drives and smartphones, enabling direct play of digital music files. This is particularly handy for users who prefer to store their music collections on portable devices.

The DPX-MP2090U also features Bluetooth connectivity, allowing for hands-free calling and wireless audio streaming. This technology provides an added layer of convenience, enabling drivers to focus on the road while still enjoying their music and staying connected. The built-in microphone ensures clear communication during calls, making it an excellent option for those who prioritize safety.

Another notable characteristic is its customizable sound settings. The audio processing capabilities include a 13-band graphic equalizer, allowing users to fine-tune their audio output according to personal preferences and vehicle acoustics. The stereo also supports high- and low-pass filters and offers adjustable bass boost options for enhanced sound dynamics.

The design of the Kenwood DPX-MP2090U is equally appealing. With a bright, easy-to-read LCD display, it provides clear visibility of song titles, artist names, and other information, even in bright sunlight. The user interface is intuitive, making navigation through menus and settings quick and easy, enhancing overall user experience.

Furthermore, the DPX-MP2090U is designed to be compatible with a range of additional features such as satellite radio and various smartphone integration options, ensuring that it remains relevant in an ever-evolving tech landscape.

In conclusion, the Kenwood DPX-MP2090U is a compelling option for anyone looking to upgrade their car audio system. Its combination of diverse playback options, Bluetooth connectivity, customizable sound settings, and user-friendly interface makes it a robust choice for enhancing your driving experience. Whether for daily commutes or long road trips, this car stereo promises to deliver excellent audio quality and convenience.
Top Page Image Contents