Kenwood TM-V7A instruction manual Calling, Receiving

Page 61

CALLING

Note: Before making a call, store your Station code in channel A, and store the desired Station codes or Group codes in channels 1 to 5.

1Select the desired band.

2Tune to the prearranged frequency.

3Press [F], [DTSS] twice to switch Page ON.

•"PAG" appears.

•If DTSS is already ON, press this key combination once.

4Press [F] (1 s), [C.SEL].

5Turn the Tuning control, or press Mic [UP]/[DWN], to select the channel that contains the desired Station code or Group code.

6Press [OFF] or Mic [PTT] to restore the frequency display.

7Press and hold Mic [PTT].

•The selected Station code or Group code is transmitted along with your Station code.

8To switch Page OFF, press [F], [DTSS].

Note:

◆Each time you press [PTT], the microphone is inhibited and the Page code is transmitted. After establishing a contact, you can eliminate this pause by switching Page OFF.

◆When recalling either a memory channel or the Call channel with DTSS status ON while using the VFO with Page switched ON, page is given priority.

RECEIVING

1Select the desired band, and tune to the prearranged frequency.

2Switch Page ON.

3You are ready to receive a call.

•When your transceiver receives a signal encoded with your Station code or a Group code, the squelch opens, an alert sounds, and "PAG" blinks.

•If you are called with your Station code, the display shows the calling station’s code.

•If called with the Group code, the display shows the group code.

4To respond to the calling station, press Mic [PTT] while the Page code is visible on the display.

1

2

3

4

5

6

7

8

9

10 11

12

13

14

15

16

17

18

19

20 21

55

Page 60 Page 62
Image 61
Page 60 Page 62
Contents TM-V7A Thank YOU FeaturesModels Covered by this Manual One or more of the following statements may be applicable When condensation occurs inside the transceiverContents Selecting the Number of Channels Using Visual Scan Partial Reset VFO Full Reset MemorySetting Scan Limits Using Program Scan Selecting Scan Resume MethodTransceiver Lock All Lock 1200/ 9600 bps Operation Data Connector Pin FunctionsSquelch Hang Time Conventions Followed in this Manual Supplied AccessoriesInstallation Example Mobile InstallationInstallation Steps Preparation for Mobile and Fixed Station OperationMobile Operation DC Power Cable ConnectionPS-33 20.5 A, 25% duty cycle Fixed Station OperationAntenna Connection Transceiver 15 a Supplied Accessory 20 a DC Power CableReplacing Fuses Fuse Location Fuse Current RatingPacket Equipment Connections Accessory ConnectionsExternal Speakers MicrophoneEwweww Your First QSOBasic Transceiver Modes Getting AcquaintedControl Band TX-BandFront Panel Tone button Function buttonREV button LOW buttonRear Panel 3MNU button Selects the Menu modeMicrophone Indicators Function Index Transceiver GuideVFO Scan Transmit Stored To exit Guide mode, press MNU againSelecting a Band Adjusting Volume Switching Power ON/OFF Adjusting SquelchPress Band SEL to select the VHF or UHF band Turn the VOL control clockwise to increase the audio levelSelecting Frequencies Tuning ControlMicrophone UP/DWN Buttons When you finish speaking, release Mic PTT Selecting Output PowerHigh Medium Low No Indicator TransmittingMenu Access What is a MENU?Select the desired band Description Selections Menu ConfigurationMulti-function Button Label See reference Memory Channel LockoutItem No Description Selections Default Compared to simplex communication, you can usually Operating Through Repeaters+600 kHz +5 MHz +1.6 MHz Not applicableSimplex Selecting Offset DirectionActivating Tone Function Selecting Offset FrequencyFreq Selecting a Tone FrequencyThis complies with the standard Arrl band plan Automatic Repeater Offset A./ Canada/ Europe OnlyEuropean versions Press s, then select Item No Auto OffsetReverse Function To cancel ASC, press REVAutomatic Simplex Checker ASC Simplex or Split Memory CHANNEL? Memory ChannelsParameter Simplex Split ChannelVHF Band UHF Band VHF/UHF Memory Channel RatioPress SET, then select the desired ratio Press SET againStoring Data in Split Channels Storing Data in Simplex Channels31, or the Call channel Recalling Memory Channels Press MHz+ Power onClearing Memory Channels Press MR againNaming Memory Channels Call Channel Changing Call Channel Contents SimplexRecalling the Call Channel Channel Display Function Changing Call Channel Contents SplitFull Reset Memory Partial Reset VFOInitializing Memory Programmable Information Programmable Memory PMTransceiver default environment. You will not lose SolutionContents of any memory channels Application ExamplesConfirm that the following conditions have been Satisfied Storing Data in PM ChannelsPress 1 to 4 corresponding to the desired PM channel Press 1 to 4 corresponding to the desired PM ChannelPress CALL+ Power on Resetting Programmable MemoryAuto PM Channel Storing Press s, then select Item No PM Auto StoreScan Type Scan Range ScanSelecting the Number of Channels Visual ScanUsing Visual Scan Selecting Scan Resume Method Scan Resume MethodsVFO Scan allows you to scan all frequencies from Memory ScanCurrent frequency step size is used Locking Out Memory Channels Press SET to toggle Lockout on or OFF defaultPress s, then select item No Lock Out Program Scan Setting Scan LimitsMHz Scan Using Program ScanCALL/VFO Scan When you are called Using CtcssWhen you make a call Press and hold Mic PTT Continuous Tone Coded Squelch System CtcssStoring Dtss Codes Dual Tone Squelch System DtssPress s Repeat Steps 4 and 5 to select the second and thirdWhen you make a call Using DtssSelect the appropriate Dtss code Press and hold Mic PTT to transmit your Dtss codePress s, then select Item No CSQ Delay Press MNU to enter Menu mode Select Menu No Code SquelchPress MNU again to exit Menu mode Dtss and RepeatersCommunication Network Example Code MemoryMember Ch. a 222 333 444 78915 4 Use the Tuning To switch Page OFF, press F, DtssStoring page Codes Channel a Control or Mic UP/DWN to selectReceiving CallingLocking OUT page Codes Dtss and Repeaters page 52. This setting isShared with Dtss Press s, then select Item No PAG Cancel Auto page CancelAnswer Back U.S.A./ Canada only Press s, then select Item No Answer BackAutopatch U.S.A. and Canada Dual Tone MULTI-FREQUENCY Dtmf FunctionsMic Keypad Confirmation Tones Press SET to complete setting Press MNU to enter Menu mode Select Menu No Dtmf MemoryTransmitting Stored Dtmf Numbers Confirming Stored Dtmf NumbersPress Mic PTT + PF Press Mic 0 to 9 to select the desired channelPress MNU to enter Menu mode Select Menu No APO TIME-OUT Timer TOTPress SET to toggle the function on or OFF default Auxiliary FunctionsAdvanced Intercept Point AIP C. will temporarily switch the RX only band to the TXBand. This function allows you to reply to a caller without Manually selecting the correct bandDual Band RX ConfigurationVHF and UHF VHF or UHF VHF and VHF UHF and UHFProgrammable VFO Switching AM/FM Mode Some Versions only10, 15, 20 or 50 kHz 25, 12.5 or 25 kHz Changing Frequency Step SizeDisplayed Frequency 00, 05, 10 20, 25, 30 40, 45, 50 60, 65, 70 80, 85, 90Press s, then select Item No Beep Volume Changing Beep VolumeLabels after Pressing F Press s, then select Item NoTransceiver Lock LockAll Lock Press F, MHz to toggle Transceiver Lock on or OFFSquelch Hang Time Meter SquelchDisplay Demonstration Mode POWER-ON MessagePress s, then select Item No Power On Msg Press VFODisplay Dimmer Changing Display ConditionsAuto Dimmer Change Press SET to toggle Negative default or Positive Press s , then select Item No Reverse ModeDisplay Contrast Positive/Negative ReversalDefault Function Configuring Program Function Keys+ Mic KEY PWR switch Tuning control VOL control SQL control Monitor User SettingEnter VoiceOperating Frequency Entry Keypad Direct EntryUse the Mic keypad to enter the desired frequency 12.5 62.5 37.5 87.5Tone Frequency Number Entry Memory Channel Number EntryUse the Mic keypad to enter 2 or 3 digits VOL SQL Microphone Control Key Function Squelch Adjustment2Key Key FunctionPress s, then select Item No Mic Control Activating Microphone ControlConnect this transceiver to your personal computer via a Packet Operation1200 bps 9600 bpsPin Function Data Connector Pin FunctionsCROSS-BAND Repeater Repeater Function U.S.A./ Canada onlyLOCKED-BAND Repeater TX HoldVS-3 Voice Synthesizer Optional Key Pressed New Mode AnnouncementCall Channel Programmable Memory MenuPage Replace the upper cover 5 screws Installing OptionsWhen the release switch clicks, the front panel is secured DFK-3C Installation ExamplesService MaintenanceService Note CleaningProblem Probable Cause Corrective Action TroubleshootingSecurely to the main unit by using the same PTT General SpecificationsReceiver TransmitterIndex
Related manuals
Manual 100 pages 58.98 Kb

TM-V7A specifications

The Kenwood TM-V7A is a sophisticated dual-band transceiver that has garnered the attention of amateur radio enthusiasts worldwide. Designed for VHF and UHF operations, it offers a plethora of features that enhance communication capabilities and provide a robust user experience.

One of the standout characteristics of the TM-V7A is its dual-vfo (variable frequency oscillator) configuration, which allows users to monitor two frequencies simultaneously. This feature is particularly useful for coordinating communications across different bands or for listening to two channels at once. The large, bright LCD display provides clear visibility of the operating frequency, with the ability to monitor a wealth of information, including received signal strength and battery voltage.

The TM-V7A supports a wide range of operating modes, including FM, AM, and SSB, making it versatile enough for different communication needs. The device is compatible with CTCSS (Continuous Tone-Coded Squelch System) and DCS (Digital-Coded Squelch), which adds significant convenience for group communications by reducing unwanted noise and interference.

Another important feature is its built-in APRS (Automatic Packet Reporting System) functionality. This allows operators to transmit their position automatically and share information with other APRS users. The built-in GPS capability enhances this feature, providing accurate location tracking that can be particularly beneficial during emergency response situations or for outdoor events.

For enhanced audio quality, the TM-V7A is equipped with a high-performance audio filter and variable bandwidth control. This allows operators to tailor the audio output based on the conditions of the band and personal preferences, improving clarity and intelligibility during conversations.

The transceiver is also designed with user-friendly navigation. The intuitive menu system enables easy access to settings and configurations, allowing operators of all experience levels to operate the radio effectively. Customization options further enhance user experience, with programmable memories allowing operators to save frequently used frequencies and settings.

The Kenwood TM-V7A’s rugged build quality ensures durability, making it suitable for both home and field operations. Its compact design allows for easy installation in vehicles or portable setups, making it an excellent choice for both casual users and serious amateur radio operators. Overall, the Kenwood TM-V7A stands out as a feature-rich transceiver capable of meeting the diverse needs of the amateur radio community, combining advanced technology with practical functionality.
Top Page Image Contents