Kenwood KVT-911DVD Using the Relay Connector Accessory G, Installation Procedure

Page 57

Installation Procedure

1.To prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery.

2.Make the proper input and output cable connections for each unit.

3.Connect the wiring harness wires in the following order: ground, battery, ignition.

4.Connect the wiring harness connector to the unit.

5.Install the unit in your car.

6.Reconnect the · terminal of the battery.

7.Press the reset button. (See p. 4)

2CAUTION

If your car's ignition does not come with an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source that receives a constant voltage supply, as with battery wires, the battery may die.

If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating.

Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits do not remove the caps from unused terminals or from the ends of the unconnected wires.

After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

Insulate unconnected wires with vinyl tape or other similar material.

Thoroughly wipe away oil and other dirt from the

installation surface.

Please avoid installation on uneven surfaces.

Mount the unit so that the mounting angle is 30° or less.

Do not install the receiver unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.

Using the Relay Connector (Accessory G)

1 Plug the vehicle's harness into

3 Lock the cable clamp.

the relay connector.

 

2Plug the parking brake detection wire into the relay connector.

4Press down using pliers until the conductive metal is even with the plastic surface.

5Lock the lid.

 

 

Cable clamp

 

Vehicle

Relay

 

Lid

connector

3

5

harness

2

 

 

 

 

 

 

4

 

1

 

 

 

Detection wire

 

Conductive metal

57

Image 57
Contents KVT-911DVD Contents Name Set Function FCC Warning Before UseCleaning the disc slot 169 LB Icon DescriptionGlossary Switching the Monitor’s Picture Power OffMonitor Control Function Opening/Closing the MonitorAdjusting the Picture Quality/ Slide Position Selecting the TV/Video Screen ModeSwitching the AV Output Adjusting the VolumeMenu Function Setup Menu Function System Setup Function Setting the On Screen Display Function Setting the Auto Scroll Display FunctionSwitching to the Sensor Box Screen SettingScreen tthe Information on the GraphicAdjusting the Time Manually Clock Adjustment FunctionData sent from RDS stations after receiving Set the time manually if the automatic timePage DVD,VCD Setup Function Setting the Priority Language for MenuSetting the Angle Mark Display Switching to the Rating Level parental lock Setting Screen Setting the Optical Output ModeScreen Mode 43 LB 43 PS 169 PBCPlayback Control Function On/Off for VCD versionInputing the Language Code Returning to the DVD setup ScreenReturning to the Original Language Audio language onlyLanguage List of language codesSetting the Parental Level Setting the passwordAdjusting the Touch Position Touch Panel Adjustment FunctionCanceling the Security Code Screen Using the Security SystemIf you press the Reset button or remove BatteryOperating the Buttons for Basic Function Basic Operation for Source Control Screen Displaying the TV Picture Selecting the Preset BandsSelecting the Channels Displaying the InformationTV Control Function Switching the List Recalling a Preset channelReturning to the Source Control Screen Tuning Selecting the FM Bands Station Preset MemorySwitching to the PTY Search Screen FM/AM Tuner Control FunctionSwitching the Band List Switching to the FM/AM List ScreenSwitching Display for Radio Text Switching the Snps and PS NamePresetting the Volume for Traffic Information Turning TI function On/OffSeeking to a Different Traffic Information Station Registration of a station as a PTY Select the type of program to be receivedSearching the Selected Program Type You can register a station as a program typeDVD/VCD Control Function on the Pictures Displaying the VCD Picture Viewing ZoomNext Play/ Previous Play Track SearchDVD/VCD/CD Control Function Pausing and Restarting Disc Play Track Scan Function Track Repeat FunctionTrack Random Play Function Selecting the Name or Title Display for Discs To Scroll ManuallySelecting the Time Display External Disc Control Function Making a Forward Track SearchMaking a Reverse Track Search Disc Repeat Function Magazine Random Play FunctionSelecting the Time Display for CDs Switching the Display for Discs Switching to the Disc List ScreenChanging the Disc List Selecting the DiscName Set Function Station Name Preset Snps /Disc Name Preset DnpsReturning to the System setup Screen Setting the MenuOther Source Control Function Weather Band Tuner Control ScreenGraphic Screen Function Sound Effect Menu Function Audio Control Function Recalling the Kenwood Preset Sound Switching to the Sound Preset ScreenAdjusting the Center Frequency of the Bass Adjusting the Bass Quality FactorAdjusting the High-pass filter for Front output Adjusting the High-pass filter for Rear outputSetting the phase for Non-Fading output Returning to the Sound Effect Menu ScreenChannels Surround Processor Control Function Setting the Room Size Mode Selecting the Position ModeTest Signal Setting the Channel BalanceAdjusting the Front Left Speaker Adjusting the Front Right SpeakerStoring Your Settings of the Crossover network/Delay time Setting the phase for Sub Woofer outputSwitching to the Delay Time Setting Screen Adjustingoutput the High-pass filter for CenterDelay Time Setting Screen Adjusting the Sub WooferAdjusting the Center Frequency Selecting the Adjust BandAdjusting the Quality Factor Adjusting the GainRecalling Your Sound Settings Recalling Your Settings of the Crossover Network/Delay timeBasic Source Control Function Remote Control FunctionMonitor Control Function TV or AUD position TV Control Function TV positionExternal Disc Control Function AUD position DVD/VCD/CD Control Function DVD positionAccessories InstallationInstallation Procedure Using the Relay Connector Accessory GMonitor unit ConnectionFront side Connection for Disc Changer and Disc Player Connection for AV EquipmentsExample When two CD/MD changers are interconnectedInstallation for Receiver unit Installation for Monitor UnitRemoving the Hard Rubber Frame Removing Monitor UnitConnect the antenna cable to receiver unit Installing the Antenna UnitsProblem Possible Cause Solution Troubleshooting GuideExternal disc control mode BUS-E50 BUS-E11 DVD Player Section Specifications