Alpine CDA-7865R Display Angle Adjustment Turning Loudness On/Off, Adjusting Volume/Bass/Treble

Page 7

Display Angle Adjustment

 

Turning Loudness On/Off

Movable display

The movable display may be adjusted to 3 different angles depending upon user preference.

1 Press the ANGLE 8 or 9 button to adjust the angle of the movable display.

NOTES

The display will close a half minute after the ignition key is turned to the OFF position.

The adjusted angle of the display is stored in memory. There is no need to re-adjust the angle when the power is turned back on.

CAUTION

Keep hands (or any other object) away from the display while it is opening or closing to avoid damage or injury. The back of the movable display will get very warm under normal operating conditions. This is not a malfunction. Do not touch.

Adjusting Volume/Bass/Treble/

Balance (Between Left and Right)/

Fader (Between Front and Rear)

1 Press the MODE (Audio Control) knob repeatedly to choose the desired mode. Each press changes the modes as follows:

VOL BAS TRE

FADBAL

NOTES

If the MODE (Audio Control) knob is not rotated in 5 seconds after selecting the BASS, TREBLE, BALANCE, or FADER mode, the unit automatically returns to the VOLUME mode.

When the subwoofer or BBE mode is ON, their respective levels may be adjusted.

2 Rotate the MODE (Audio Control) knob until the desired sound is obtained in each mode.

NOTES

The settings of the Bass and Treble will be individually memorized for each source (FM, MW (LW) and CD) until the setting is changed. Depending on the connected devices, some functions and display indications do not work.

When the temperature inside the unit rises, the volume may decrease momentarily. This is not a malfunction.

Loudness introduces a special low- and high- frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.

1 Press and hold the MODE (Audio Control) knob for at least 2 seconds to activate or deactivate the loudness mode.

The display shows "LOUDNESS" when the loudness mode is activated.

NOTE

When an external audio processor is connected to this unit, the Loudness function on this unit does not work.

Selecting BBE Mode

The BBE (Barcus Berry Electronics) processor installed in this unit is designed to correct the phase distortion inherent in most loudspeaker designs. Ensuring the phase integrity of the signal driving the speakers improves the accurate reproduction of the sound.

1 Press and hold the BBE button for at least 2 seconds to turn on and off the BBE mode.

2 In BBE mode, press the MODE (Audio Control) knob to select the BBE adjusting mode.

Each press changes the adjusting mode.

3 To change to a desired BBE level, rotate the MODE (Audio Control) knob.

The BBE level can be changed from +1 to +3.

NOTE

The initial mode is +2.

5-EN

Image 7
Contents CDA-7865R Alpine CD Changers Give You More Contents Precautions Handling the Detachable Front Panel Initial System Start-Up Turning Power On and OffBasic Operation Detaching the Front PanelFader Between Front and Rear Display Angle Adjustment Turning Loudness On/OffAdjusting Volume/Bass/Treble Selecting BBE ModeDemo ← AUX ← SCR ← Mute ← Beep ← Adjusting Source Signal LevelChanging Backlighting Colour Dimmer ControlSound Beep Guide Function Turning Mute Mode On/OffCD Text Scroll Setting Subwoofer On and Off→ Tuner → CD → AUX Setting the AUX Mode DemonstrationDemo OFF Switching the Display Modes Adjusting the built -in Audio ProcessorDefault values BC 80 Hz BW WIDE1 TC 10.0kHz Automatic Seek Tuning Manual TuningRadio Operation Tuning to Preset Stations Automatic Memory of Station PresetsAuto Station Search While Travelling Press the AF button to deactivate the RDS mode Setting RDS Reception Mode and Receiving RDS StationsRecalling Preset RDS Stations When the RDS station signal received has become weak→ Light M → Classics → Other M PTY Programme Type TuningReceiving RDS Regional Local Stations Receiving Traffic InformationReceiving Traffic Information While Playing CD or Radio When traffic information stations cannot be receivedPriority PTY Programme Type Displaying Radio Text Turning Emergency Alarm On or OffPress the c button Movable display will open CD Player OperationOpening and Closing the Movable display PlaybackX. Random Play Music Sensor SkipFast Forward and Backward Repeat PlayAbout Title and Text Displaying the Title/Text Titling DiscsErasing Disc Title When a 12-disc CD Changer is connectedControlling CD Changer Optional Searching for Titled Discs CD Changer only Multi-Changer SelectionPress the button to change to the CD changer operation Remote Control OperationControls on Remote Control Press the switch to turn the power on/offBattery Replacement Case of Difficulty InformationNo Magzn FM Tuner Section SpecificationsPrecautions Installation and ConnectionsRemoval InstallationISO Antenna Convertor Plug ConnectionTo prevent external noise from entering the audio system 30-EN