Alpine PXA-H700 owner manual Installation and Connections, Do not Splice Into Electrical Cables

Page 32

Installation and Connections

Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.

Warning

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, fire or electric shock.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR

STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

USE THE CORRECT AMPERE RATING WHEN

REPLACING FUSES.

Failure to do so may result in fire or electric shock.

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT INSTALL THE MONITOR NEAR THE

PASSENGER SEAT AIR BAG.

If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries.

DO NOT BLOCK VENTS OR RADIATOR PANELS.

Doing so may cause heat to build up inside and may result in fire.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE

STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

30-EN

Image 32
Contents PXA-H700 Page Contents Still Hear Outside Noise While Driving Maintenance TemperatureInstallation Location Turning the power on and off About indicatorsSetting the speakers Basic OperationUsing with Ai-NET connections Switching the inputAdjusting the input level Adjusting the volume, balance, fader and subwooferAutomatic Adjustments YES noError Settings/Adjustments Concrete examplesCR / P H a S E L F 1 R R Settings/Adjustments Bass FocusExample of Steps 4 and 5 Setting Time difference TableAdjustable frequencies Settings/AdjustmentsGraphic equalizer adjustments Parametric equalizer adjustments Q P F r o n t L N D 3 5 k H z + 7 d B14-EN Over Over adjustment When L or R is selectedHint for adjusting the low range Hint for adjusting the subwooferHints for adjusting the high range MX settings 18-ENBass COMP. setting Using Dolby Surround Using the Pro Logic II modeAdjustment procedure for Dolby Surround Speaker setup Adjusting the speaker levelsAdjusting the level for individual speakers manual Mixing bass sound to the rear channelUsing Dolby Surround Adjusting the acoustic imageAchieving powerful high volume sound Adjusting the DVD levelNavigation system voice guidance interruption Linear PCM settingConvenient Functions Display settings MX mode setting Ai-NET connectionCalling out stored values Storing settings in the memoryDefeat mode Switching the display mode Switching the color of the illuminationInstallation and Connections Do not Splice Into Electrical CablesFuse PrecautionsWiring Connections Accessories To prevent external noise from entering the audio systemInstallation Installation using Velcro fastenerMounting the control unit Mounting other unitsFlush Mounting the control unit Velcro Fastener Mounting Using the Mounting Screws SuppliedMounting the base unit Basic Connections Diagram Terminal specifications Connect toPlease observe the following when using Fiber Optic Cable Examples of system expansion38-EN PXA-H700 + Head Unit + Video Deck etc. + External Amplifier 40-EN Information TerminologyOthers Case of difficultyComponents Parts name Quantity SpecificationsDimensions Limited Warranty