Setting EQ mode
This setting gives you a choice of
equalizer.
1 Press and hold FUNC./SETUP for at least 2 seconds to setup the Selection mode.
2 Turn the Rotary encoder to select AUDIO mode, and then press ~ III lENT.
Bluetooth H GENERAL H AUDIO H DISPLAY H
TUNER* H Bluetooth
*Only when HD Radio/SAT Radio is connected.
3 Turn the Rotary encoder to select EQ Mode, and then press ~ III lENT.
4 Turn the Rotary encoder to select the desired equalizer characteristic, and then press ~ III lENT.
Parametric EO | Graphic EO |
(Initial setting) |
|
PEQ:
GEQ:
5 Press and hold FUNC./SETUP for at least 2 seconds to return to normal mode.
•Pressing ~ /RTN during the procedure will return to the previous mode.
•If no operation is performed for 60 seconds in the SETUP mode, the setting mode is canceled.
•This function is inoperable when DEFEAT is set to ON (page 13).
•Press and hold ~ IESC for at least 2 seconds, the setting mode is canceled.
Adjusting and Storing the Parametric Equalizer Curve
You can modify the Equalizer settings to create a response curve more appealing to your personal taste. To adjust the Parametric Equalizer Curve, set the EQ mode to Parametric EQ. For details, refer to "Setting EQ mode" (page 14).
1 Press A.SEL to recall the DSP adjust mode.
Media Xpander H Crossover H T.Correction H
Parametric EO/Graphic EO H Media Xpander
2 Turn the Rotary encoder to select Parametric EQ mode, and then press ~/II/ENT.
3 Press BAND to select the band to be adjusted.
Band1 ~ Band2 ~ Band3 ~ Band4 ~ Band5 ~ Band1
4 Press ~ or ~ to select frequency bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
5 Turn the Rotary encoder to adjust the level.
Adjustable level:
6 Press SOURCE/<b to set the bandwidth (Q).
Adjustable bandwidth: 1f 1.5, 3
7 To adjust another band, repeat steps 3 to 6 and adjust all bands.
8 When the setting has been completed, select any one of the preset buttons (1 through 6), press and hold the desired preset buttons for at least 2 seconds.
9 Turn the Rotary encoder to select PROTECT YES/NO, and then press ~ III lENT to store the adjusted contents.
PROTECT YES | PROTECT NO |
(Initial setting) |
|
•If YES is selected, the adjusted contents are protected and stored into the preset buttons. When you want to store the parameter into a protected prest!t button, "REPLACE NOIYES" can be selected.
•IfNO is selected, the preset is'stored.
10 After setting, press and hold ~/ESC for at least 2 seconds to return to normal mode.
•The frequencies ofadjacent bands cannot be adjusted within 4 steps.
•This function is inoperable when DEFEAT is set to ON (page 13).
•While adjusting the Parametric EQ, you should consider the frequency response of the connected speakers.
•The stored contents are not deleted even when resetting the unit or disconnecting the battery.
•The stored contents can be recalled by performing operation in "Recalling the Stored Equalizer Curve" (page 15).
•Pressing ~ IRTN when Parametric EQ is adjusted will return to the previous item.
•If MultEQ is turned on, the A.SEL button is ineffective. For details, refer to "Turning MultEQ on/off" (page 13).
•Ifno operation is performedfor 60 seconds, the unit will return to the normal mode.
Adjusting and Storing the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more appealing to your personal taste. To adjust the graphic equalizer curve, set the EQ mode to Graphic EQ. For details, refer to '~Setting EQ mode" (page 14).
1 Press A.SEL to recall the DSP adjust mode.
Media Xpander H Crossover H T.Correction H
Parametric EO/Graphic EO, H Media Xpander
2 Turn the Rotary encoder to select Graphic EQ mode, and then press ~/II/ENT.
3 Press BAND to select the band to be adjusted.
Band1 ~ Band2 ~ Band3 ~ Band4 ~ Band5 ~ Band6 ~ Band7 ~ Band 1