Alpine CDA-9887 owner manual 35-EN, Case of Difficulty

Page 37

Information

In Case of Difficulty

If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.

No function or display.

Vehicle's ignition is off.

-If connected following instructions, the unit will not operate with the vehicle's ignition off.

Improper power lead (Red) and battery lead (Yellow) connections.

-Check power lead and battery lead connections. Blown fuse.

-Check the fuse of the unit; replace with the proper value if

necessary.

Intemalmicro-computer malfunctioned due to interference noise etc.

-Press the RESET switch with a ballpoint pen or other pointed article.

Unable to receive stations.

•No antenna or open connection in cable.

-Make sure the antenna is properly connected; replace the antenna or cable if necessary.

Unable to tune stations in the seek mode.

You are in a weak signal area.

- Make sure the tuner is in the DX mode.

If the area you are in is a primary signal area, the antenna may not be grounded and connected properly.

-Check your antenna connections; make sure the antenna is properly grounded at its mounting location.

The antenna may not be the proper length.

-Make sure the antenna is fully extended; if broken, replace the antenna with a new one.

Broadcast is noisy.

•The antenna is not the proper length.

-Extend the antenna fully; replace it if it is broken.

•The antenna is poorly grounded.

-Make sure the antenna is grounded properly at its mounting location.

CD Player/Changer not functioning.

•Out of operating temperature range +50°C (+1200 P) for CD. - Allow the vehicle's interior (or trunk) temperature to cool.

CD playback sound is wavering.

•Moisture condensation in the CD Module.

-Allow enough time for the condensation to evaporate (about 1 hour).

CD insertion not possible.

•A CD is already in the CD player.

-Eject the CD and remove it.

•The CD is being improperly inserted.

-Make sure the CD is being inserted following instructions in the CD Player Operation section.

Unable to fast forward or backward the CD.

•The CD has been damaged.

-Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism.

CD playback sound skips due to vibration.

Improper mounting of the unit.

-Securely re-mount the unit. The disc is very dirty.

-Clean the disc.

The disc has scratches. - Change the disc.

The pick-up lens is dirty.

-Do not use a commercially available lens cleaner disc. Consult your nearest Alpine dealer.

CD playback sound skips without vibration.

•The disc is dirty or scratched.

- Clean the disc; damaged disc should be replaced.

Error displays (built-in CD player only).

•Mechanical error.

-Press ~. After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest Alpine dealer.

CD-R1CD-RW playback not possible.

•Close session (finalization) has not been performed. - Perform finalization and attempt playback again.

MP3, WMA or AAC is not played back.

•Writing error occurred. The CD format is not compatible.

-Make sure the CD has been written in a supported format. Refer to "About MP3IWMAIAAC" (pages 11-12), then rewrite in the format supported by this device.

The sound is not output from the speakers.

•Unit has no output signal of the internal amplifier. - Power IC is switched to "ON" (page 23).

iPod does not play and no sound is output.

•The iPod has not been recognized.

-Reset this unit and the iPod. Refer to "Initial System Start-Up" (page 7). To reset the iPod, refer to the Owner's Manual of the iPod.

35-EN

Page 36 Page 38
Image 37
Page 36 Page 38
Contents CDA-9887 Intended Contents Operating Instructions Installation and Connections Operating Instructions ~ ~ Illo§@ Turning Power On and Off Accessory ListPress SOURCE/! to turn on the unit Lowering Volume Quickly Adjusting VolumeSetting the Time and Calendar Initial System Start-UpTuning to Preset Stations Presetting Stations AutomaticallyPress TUNE/A.ME to select the tuning mode Listening to RadioPlayback Frequency Search FunctionPress .z Open Insert a disc with the label side facing upX. Random Play Repeat PlayQuick Search Searching from CD TextAbout MP3/WMA/AAC Press ~/ESe during playID3 tagsIWMA tags Supported playback sampling rates and bit ratesProducing MP3IWMAJAAC discs Media supportedPress MultEQ to select ON/OFF mode Equalizer PresetsEach press changes the mode as follows Turning MultEQ on/offAdjusting and Storing the Parametric Equalizer Curve Setting EQ modeAdjusting and Storing the Graphic Equalizer Curve Recalling the ,Stored Equalizer Curve About the CrossoverAdjusting and Storing the Crossover Settings = distance to farthest speaker distance to other speakers About Time CorrectionAdjusting and Storing the Time Correction Setting the Time Correction UnitSetting the MX Mode Recalling the Stored Time Correction SettingsPress Title Displaying the TextDisplay will change every time the button is pressed About the indication displayDisplaying Time Blackout Mode On and OffPress Title repeatedly until the time is displayed About TextBirthday Opening Message Setting Birthday Set Setting the Bluetooth in ConnectionSetting the Clock Display Clock Mode 22-EN23-EN 24-EN Receiving Channels with the SAT Radio Receiver Optional 25-EN26-EN Storing Channel PresetsChecking the SAT Radio ID Number Receiving Stored ChannelsPress FUNC./SETUP to cancel the function mode Canceling the stored Alert Memory Sirius only27-EN Search FunctionQuick Search Function 28-ENReceiving Weather or Traffic Information from SAT Radio Instant Replay Function Sirius onlyPlayback 29-ENSearching for a desired Song 30-ENDirect Search Function For example Searching by Artist nameRepeat Play 31-ENRandom Play Shuffle M.I.X Displaying the TextControlling CD Changer Optional 32-ENPlaying MP3 Files with the CD Changer Optional Multi-Changer Selection OptionalOperating the Audio Processor Controls on Remote Control~ UP Button Opening the battery cover Battery ReplacementReplacing the battery Closing the coverCase of Difficulty 35-EN36-EN High TemperatureOFF AIR Specifications38-EN Installation and Connections~+R InstallationPull the unit out, keeping it unlocked as you do so EQ/DIVL~ 40-ENSwitched Power Lead Ignition Red CD Antenna Receptacle Power Antenna Lead BlueBattery Lead Yellow Remote Turn-On Lead BluelWhiteTo prevent external noise from entering the audio system 42-ENALPINE-1 FfffMLPINELimited Warranty Repetez les etapes 3 et 4 pour regler une autre enceinte Repeat steps 3 and 4 to set another speakerRepita los pasos 3 y 4 para ajustar otro altavoz Upprepa steg 3 till 4 om du viti stilla in fler h6gtalare Per configurare un altro altoparlante, ripetere i punti 3 e~Rotary encoder flAtiiell 0.0 ~ 336.6 em 14E$t Rotary encoder iJ!JiSJeil 0.0 ~ 336.6 emCassette Player Monitor Controller CD Player Video Monitor Factory installed Alpine OtherMD Player Navigation DVD Player Mobile Mayday CD Changer Video Tape PlayerBusiness Reply Mail PERrtIT no International Business Reply MAIL/REPONSE Payee
Top Page Image Contents