Sony MZ-R91 VDC0, Swdt, Sclk, VSC0, Srdt, Sens, Sqsy, Dqsy, Recp, VDIO0, Osci, Osco, VSIO0, VSC1

•MAIN BOARD IC502 CXD2660GA

(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 16M BIT D-RAM)

Pin No.	Pin Name		I/O		Description
1		VDC0	—	Power supply terminal (+1.8V) (for internal logic)
2		MNT0	I/O	Not used (open)
3		MNT1	O	Recording shock detect signal output to the system controller (IC801)
4		MNT2	O	Off track signal output to the SN761056ADBT (IC501) and system controller (IC801)
5		MNT3	O	Focus OK signal output to the system controller (IC801)
				“H”: is output when focus is on (“L”: NG)
6		SWDT	I	Serial data input from the system controller (IC801)
7		SCLK	I (S)	Serial clock signal input from the system controller (IC801)
8		XLAT	I (S)	Serial data latch pulse input from the system controller (IC801)
9		VSC0	—	Ground terminal (for internal logic)
10		SRDT	O (3)	Serial data output to the system controller (IC801)
11		SENS	O (3)	Internal status (SENSE) output to the system controller (IC801)
12		XRST	I (S)	Reset signal input from the system controller (IC801) “L”: reset
13		SQSY	O	Subcode Q sync (SCOR) output the system controller (IC801)
				“L” is output every 13.3 msec	Almost all, “H” is output
14		DQSY	O	Digital In U-bit CD format subcode Q sync (SCOR) output to the system controller (IC801)
	(MTFLGL)			“L” is output every 13.3 msec	Almost all, “H” is output
15		RECP	I	Laser power selection signal input from the system controller (IC801)
				“L”: playback mode, “H”: recording mode
16		XINT	O	Interrupt status output to the system controller (IC801)
17		TX	I	Recording data output enable signal input from the system controller (IC801)
				Writing data transmission timing input
18		VDIO0	—	Power supply terminal (+2.4V) (for I/O)
19		OSCI	I	System clock (512Fs=22.5792 MHz) input terminal
20		OSCO	O	System clock (512Fs=22.5792 MHz) output terminal
21		VSIO0	—	Ground terminal (for I/O)
22 to 29		NC	—	Not used (open)
30		VSC1	—	Ground terminal (for internal logic)
31		XTSL	I	Input terminal for the system clock frequency setting
				“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)
32	XCS_DSP		I	Chip select signal input from the system controller (IC801)
33		DIN1	I	Digital audio signal input terminal when recording mode
34		DOUT	O	Digital audio signal output terminal when playback mode Not used (open)
35		DT72	O	Not used (open)
36, 37	VDC1, VDC2		—	Power supply terminal (+1.8V) (for internal logic)
38		DATAI	I	Serial data input terminal Not used (fixed at “L”)
39		LRCKI	I	L/R sampling clock signal (44.1 kHz) input terminal
				“L”: Rch, “H”: Lch Not used (fixed at “L”)
40		XBCKI	I	Serial input/output data bit clock signal (2.8224 MHz) input terminal Not used (fixed at “L”)
41		ADDT	I	Recording data signal input from the A/D, D/A converter (IC301)
42		DADT	O	Playback data signal output to the A/D, D/A converter (IC301)
43		LRCK	O	L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC301)
44		VSC2	—	Ground terminal (for internal logic)
45		XBCK	O	Serial input/output data bit clock signal (2.8224 MHz) out put to the A/D, D/A converter (IC301)

* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O

– 47 –