Introduction, Features, Parts Checklist

INTRODUCTION:

Congratulations on purchasing a Gemini XL-200turntable. This state of the art turntable includes the latest features. Prior to use, we suggest that you carefully read all the instructions.

FEATURES

•±10% Pitch control:

•Strobe illuminator

•Soft-touch start/stop switch

PRECAUTIONS:

1.Read all operating instructions before using this equipment.

2.The apparatus should not be exposed to dripping or splashing, and no objects filled with liquids such as vases should be placed on the apparatus.

3.To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please contact the Gemini Service Department or your authorized dealer to speak to a qualified service technician.

4.Tone Arm bearings are factory set and sealed. Any attempt at adjustment will void the warranty.

5.Be sure that all AC power is OFF while making connections.

6.Cables should be low capacitance, shielded and of proper length. Make sure that all plugs and jacks are tight and properly connected.

7.Always begin with the audio level faders/volume controls set at minimum and the speaker volume control(s) set to OFF. Wait 8 to 10 seconds prior to turning up the speaker volume to prevent the transient “POP” that could result in speaker/crossover damage.

8.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

9.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.

PARTS CHECKLIST:
Turntable unit	1
Dust cover hinge	2
Turntable platter	1
45 RPM adapter	1
Slipmat	1
Counter balance	1
Dust cover	1
Headshell	1
ASSEMBLY AND SET-UP:
NOTE: SEE FIG. 1 FOR PART NUMBERS AND LOCATIONS.

VOLTAGE SELECTION:

Rotate the PLATTER (2) until the VOLTAGE SELECTOR (3) (located on the TURNTABLE BASE (1)) is visible through one of the platter holes. Make sure that the VOLTAGE SELECTOR switch is set to the correct voltage. WARNING: If you try to operate the turntable with the incorrect voltage setting, it can damage your turntable.

ATTACHING THE TURNTABLE BELT:

The TURNTABLE BELT (4A) comes attached to the PLATTER (2) and the MOTOR SPINDLE (4B) but can some times detach in shipping. Rotate the PLATTER (2) and look through the platter holes to check if belt detached. If the belt is not wrapped tightly around the platter and the MOTOR SPINDLE, you need to reattach it.

1.Remove the platter and wrap the belt around the inner circle under the platter. DO NOT STRETCH OUT THE BELT.

2.Replace the platter and rotate the PLATTER (2) until the MOTOR SPINDLE (4B) is visible, then fit your fingers in hole on the top of the PLATTER (2), feel for and grab the rubber belt and attach to the motor spindle.

3.Replace the locking washer.

TURNTABLE INSTALLATION:

1.Put the SLIPMAT (5) on the PLATTER (2).

2.Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Use the turntable feet to horizontally stabilize the unit.

3.Try to place the unit as far away from the speakers as possible.

4.Keep the unit away from direct exposure to the sun, heat, moisture or dirt.

5.Keep the unit well ventilated.

CARTRIDGE INSTALLATION: (SEE FIG. 2)

Because all cartridges have their own designs, please refer to your particular cartridge’s instructions to insure proper installation.

1.Connect the lead wires to the cartridge terminals. For your convenience, the terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color.

White (L+)	Left Channel +
Blue (L-)	Left Channel -
Red (R+)	Right Channel +
Green (R-)	Right Channel -

2.Mount the cartridge in the HEADSHELL (6) and tighten it with the screws included with the cartridge.

ATTENTION STANTON 680 CARTRIDGE USERS

When using a Stanton 680 or similar cartridge, where the body is grounded to a cartridge terminal, remove the grounding strap from the cartridge body to the cartridge ground terminal. Failure to do this may result in excessive hum.

HEADSHELL INSTALLATION:

Insert the HEADSHELL (6) into the front of the tubular TONE ARM (7). While holding the HEADSHELL firmly in a horizontal position, turn the LOCKING NUT

(8)counter clockwise until the HEADSHELL is locked in place.

COUNTERWEIGHT INSTALLATION: (SEE FIG. 3)

1.Slide the COUNTERWEIGHT (9) onto the rear of the TONE ARM (7) with the numbered stylus gauge facing forward.

2.Twist the COUNTERWEIGHT (9) lightly counter clockwise, to screw it onto the rear of the TONE ARM (7) .

ADJUSTING HORIZONTAL ZERO (0) BALANCE AND STYLUS PRESSURE:

1.Without touching the stylus tip, remove the stylus protector (if your cartridge has a detachable one).

2.Release the ARM CLAMP (10) and lift the TONE ARM (7) off the ARM REST (11).

3.Counter clockwise advancement of the COUNTERWEIGHT (9) will cause the cartridge side of the TONE ARM (7) to be lowered. Clockwise will cause the opposite. Turn the COUNTERWEIGHT clockwise or counter clockwise as needed until the TONE ARM is balanced horizontally. You can easily tell this by watching for the point where the TONE ARM “floats” freely.

4.Place TONE ARM (7) on ARM REST (11) and lock it in place with the ARM CLAMP (10).

5.With the TONE ARM (7) locked on the ARM REST (11), hold the COUNTERWEIGHT (9) steady with one hand while rotating the STYLUS PRESSURE RING (12) until the numeral “0” on the ring aligns with the center line on the TONE ARM rear shaft. The horizontal zero (0) balance should be completed.

6.Refloat the TONE ARM to ensure horizontal zero (0) balance. If zero balance has not been maintained, repeat counterweight steps 3 - 5.

(4)

XL-200 specifications

The Gemini XL-200 is an advanced unmanned aerial vehicle (UAV) designed for a wide range of applications, offering unparalleled capabilities in surveillance, reconnaissance, and data collection. This cutting-edge drone is a product of years of innovation, combining state-of-the-art technology with outstanding performance attributes.

One of the main features of the Gemini XL-200 is its extended operational range. With a flight radius of up to 100 kilometers, this UAV can cover vast areas while remaining under remote control. This characteristic makes it particularly useful for military applications, border patrol, and disaster management, providing vital intelligence where traditional means may fall short.

Equipped with a dual propulsion system, the Gemini XL-200 can switch between electric and hybrid engines, optimizing fuel efficiency and increasing endurance. It boasts an impressive flight time of over 12 hours, allowing for prolonged missions without the need for frequent refueling. This feature is especially beneficial in scenarios requiring continuous surveillance or long-term monitoring.

The Gemini XL-200's payload capacity is another standout characteristic, supporting a variety of modular sensors and equipment. This flexibility allows operators to customize the UAV for specific missions, whether it's outfitted with high-resolution cameras, thermal imaging sensors, or even communication relays. The ability to adapt to diverse operational requirements is a significant advantage in the rapidly evolving landscape of UAV technology.

In terms of technological sophistication, the Gemini XL-200 is equipped with advanced avionics that enhance navigation and control. The integration of GPS and inertial navigation systems ensures precise positioning, while real-time data transmission capabilities facilitate instant analysis and decision-making. This robust data link technology allows for seamless integration with ground control stations and other assets.

Safety is paramount in UAV operations, and the Gemini XL-200 features multiple redundant systems to mitigate risks. These include backup power sources, custom failsafe protocols, and collision avoidance systems. Such measures ensure the UAV can operate reliably in various environments, bolstering the confidence of operators during critical missions.

In conclusion, the Gemini XL-200 represents a significant advancement in UAV technology, combining range, endurance, adaptability, and safety features. These characteristics make it an ideal choice for military, commercial, and humanitarian applications, setting a new standard in the field of unmanned aerial vehicles. As demands for efficient aerial solutions grow, the Gemini XL-200 is poised to meet and exceed expectations across multiple sectors.