Huawei MG323 manual Input Signal Control Pins, Pin for network status LED

Page 21

HUAWEI MG323 GSM M2M Module
Hardware Guide	Description of the Application Interfaces

Network status LED (LED_STATUS) pin

Table 3-4lists the pins on the signal control interface.

Table 3-4Pins on the signal control interface

Pin No.	Signal Name	I/O	Description

20	TERM_ON	I	Pin for controlling power-on and power-off

22	RESET	I	Pin for resetting the hardware

25	LED_STATUS	O	Pin for network status LED

3.5.2Input Signal Control Pins

The MG323 module implements power-on and power-off and resets the hardware through the input signal control pins.

The TERM_ON pin is used to implement power-on and power-off. If the TERM_ON pin is pulled down for 1 second to 2 seconds, the module is powered on; if the TERM_ON pin is pulled down for 1 second to 2 seconds again, the module is powered off.

The RESET pin is used to reset the hardware. When the software stops responding, the RESET pin can be pulled down for at least 10 ms to reset the hardware.

As the RESET and TERM_ON signals are relatively sensitive, it is recommended that you install a 10 nF capacitor near the RESET and TERM_ON pins of the B2B interface for filtering. In addition, when you design a circuit on the PCB of the interface board, it is recommended that the circuit length not exceed 20 mm and that the circuit be kept at a distance of 2.54 mm (100 mil) at least from the PCB edge. Furthermore, you need to wrap the area adjacent to the signal wire with a ground wire. Otherwise, the module may be reset due to interference.

Figure 3-6shows the connections of the TERM_ON and RESET pins.

	Issue 06 (2013-06-13)	Huawei Proprietary and Confidential	21
		Copyright © Huawei Technologies Co., Ltd.

Image 21

Contents Hardware Guide Issue DateNo Warranty History About This DocumentVersion Date Chapter Descriptions CreationVersion Date Chapter Descriptions Updated .8 Audio Interface Updated -3 RecommendedSpecifications of the antenna interface Contents Electrical and Reliability Features Overview IntroductionOverall Description Feature DescriptionAbout This Chapter Function OverviewDRX=5 DRX=9 DRX=2SMS Gprs Gprs ClassCircuit Block Diagram Application Block Diagram2Circuit block diagram of the MG323 module Description of the Application Interfaces B2B Connector InterfaceMin Tpy Max Pin Pin Name Description DC Characteristics NormalTermon ResetUART1DCD LedstatusOverview Power InterfaceVIO VbatVbat Interface Pin No Signal Name DescriptionGND Vcoin DCEPower-On and Power-Off Time Sequence Vcoin InterfaceVIO Interface Power-On Time Sequence Pin for controlling power-on and power-offPin for resetting the hardware Signal Control Interface Power-Off Time SequenceReset Pin for network status LED Input Signal Control PinsOutput Signal Control Pin Application DeviceWorking or Network Status Uart Interface Pin No Signal Name Description Feature DirectionDCE receive DTE transmits DTE to DCE Data Serial data Circuit Recommended for the Uart InterfaceDCE data DTE is ready DTE to DCE Terminal ready DCE data set DCE is ready DCE to DTE ReadyPower supply of the SIM card Clock signal of the SIM cardData signal of the SIM card Reset signal of the SIM cardCircuit Recommended for the SIM Card Interface Ground signal of the SIM cardAudio Interface 12External circuit for 32 Ω handsets/16 Ω headsets13External circuit for the microphone interface Antenna Interface Antenna InstallationEnvironmental Type Material Condition Coaxial Cable and RF ConnectorHuawei MG323 GSM M2M Module Hardware Guide Antenna Interface Specification Minimum Typical Maximum Unit Value RF Specifications of the Antenna InterfaceESD Protection for the Antenna Interface Uplink frequency range GSM 824 849 MHzSpecification Minimum Typical Maximum Unit Value Polarization Linear polarization Pattern Omnidirectional Specifications of the Antenna InterfaceSymbol Specification Minimum Value Maximum Value Unit Electrical and Reliability FeaturesExternal power voltage Extreme Working ConditionsSpecification Minimum Value Maximum Value Unit Operating and Storage Temperatures and HumidityPin No Signal Name Electrical Criteria of Application InterfacesPower supply Function Signal Name Waveform Remarks LevelVoltage great drop. The Vbat power voltage Than 3.3Power pin Pins 41, 43, 45, 47, and 49 are power GND ExternalVBAT=0 LedstatuUART1 UART1RD UART1RINUART1DSR UART1RTS UART1DTR UART1CTS UART1DCD Input Power Supply Power Supply FeaturesWorking Current Parameter Minimum Value Typical Value Maximum Value UnitWorking Mode Typical value Unit Remark ConfigurationBand Typical Unit Configuration Value Reliability FeaturesUp/1 Down 123 Test Condition StandardTest Condition Standard ESD Features ESD Test Standard Contact Discharge Air DischargeEN61000-4-2 ±4 kV ±8 kV Mechanical Specifications DimensionsDimensions L x W x H 35 mm x 32.5 mm x 3.05 mm 1Dimensions of the MG323 module unit mm Dimensions of the B2B ConnectorModel Stacking HRS Number Height mm 5Structure fixing hole MG323 Module Installation Description6MG323 module installation 7Machine screw dimensions Specification Selection for Fasteners8Nut dimensions 1Circuits of typical interfaces in the MG323 module Appendix a Circuits of Typical InterfacesAcronym or Abbreviation Expansion Appendix B Acronyms and AbbreviationsPCB PbcchPDU RTC

Related manuals

Manual 239 pages 48.54 Kb