Huawei MG323 manual SIM Card Interface, Clock signal of the SIM card, Power supply of the SIM card

Page 25

HUAWEI MG323 GSM M2M Module

 

Hardware Guide

Description of the Application Interfaces

Figure 3-9The signal through the RING after the MG323 receives an SM

When an MG323 Module receives a voice call, a periodical low level signal for 1s and a high level signal for 4s are output by RING, as shown in Figure 3-10 .

Figure 3-10The signal through the RING after the MG323 receives a voice call

 

 

4s

 

4s

 

4s

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1s

1s

1s

For detailed application of the MG323 UART1 interface, see HUAWEI Module UART Serial Port Design Guide.

The maximum level of UART1_DCD, UART1_RING, UART1_DSR and UART1_DTR signals is 3.2 V, and the maximum level of UART1_TD, UART1_RD, UART1_CTS and UART1_RTS signals is 3.25 V. Therefore, if the UART signals need to be connected the signal with 3.3 V, a level conversion curcuit is required.

UART1 interface must be powered on after the module is powered on to avoid the wind blow in which may cause the module cannot work properly.

The level of RS-232 Transceivers must match that of the MG323 module.

3.7SIM Card Interface

3.7.1Overview

The MG323 module provides a SIM card interface complying with the ISO 7816-3 standard and supports automatic detection of a Class B SIM card or a Class C SIM card. Table 3-7lists the SIM card interface signals.

Table 3-7SIM card interface signals

Pin No.

Signal Name

I/O

Description

 

 

 

 

1

SIM_CLK

O

Clock signal of the SIM card

 

 

 

 

3

VSIM

P

Power supply of the SIM card

 

 

 

 

5

SIM_DATA

I/O

Data signal of the SIM card

 

 

 

 

7

SIM_RST

O

Reset signal of the SIM card

 

 

 

 

Issue 06 (2013-06-13)

Huawei Proprietary and Confidential

25

Copyright © Huawei Technologies Co., Ltd.

 

 

Image 25
Contents Hardware Guide Issue DateNo Warranty History About This DocumentVersion Date Chapter Descriptions CreationVersion Date Chapter Descriptions Updated -3 Recommended Updated .8 Audio InterfaceSpecifications of the antenna interface Contents Electrical and Reliability Features Overview IntroductionOverall Description Feature DescriptionAbout This Chapter Function OverviewDRX=5 DRX=9 DRX=2SMS Gprs Gprs ClassCircuit Block Diagram Application Block Diagram2Circuit block diagram of the MG323 module Description of the Application Interfaces B2B Connector InterfaceMin Tpy Max Pin Pin Name Description DC Characteristics NormalTermon ResetUART1DCD LedstatusOverview Power InterfaceVIO VbatVbat Interface Pin No Signal Name DescriptionGND Vcoin DCEVcoin Interface Power-On and Power-Off Time SequenceVIO Interface Pin for controlling power-on and power-off Power-On Time SequencePin for resetting the hardware Power-Off Time Sequence Signal Control InterfaceReset Pin for network status LED Input Signal Control PinsApplication Device Output Signal Control PinWorking or Network Status Uart Interface Pin No Signal Name Description Feature DirectionDCE receive DTE transmits DTE to DCE Data Serial data Circuit Recommended for the Uart InterfaceDCE data DTE is ready DTE to DCE Terminal ready DCE data set DCE is ready DCE to DTE ReadyPower supply of the SIM card Clock signal of the SIM cardData signal of the SIM card Reset signal of the SIM cardCircuit Recommended for the SIM Card Interface Ground signal of the SIM cardAudio Interface 12External circuit for 32 Ω handsets/16 Ω headsets13External circuit for the microphone interface Antenna Interface Antenna InstallationEnvironmental Type Material Condition Coaxial Cable and RF ConnectorHuawei MG323 GSM M2M Module Hardware Guide Antenna Interface Specification Minimum Typical Maximum Unit Value RF Specifications of the Antenna InterfaceESD Protection for the Antenna Interface Uplink frequency range GSM 824 849 MHzSpecification Minimum Typical Maximum Unit Value Polarization Linear polarization Pattern Omnidirectional Specifications of the Antenna InterfaceSymbol Specification Minimum Value Maximum Value Unit Electrical and Reliability FeaturesExternal power voltage Extreme Working ConditionsSpecification Minimum Value Maximum Value Unit Operating and Storage Temperatures and HumidityPin No Signal Name Electrical Criteria of Application InterfacesPower supply Function Signal Name Waveform Remarks LevelVoltage great drop. The Vbat power voltage Than 3.3Power pin Pins 41, 43, 45, 47, and 49 are power GND ExternalVBAT=0 LedstatuUART1RIN UART1 UART1RDUART1DSR UART1RTS UART1DTR UART1CTS UART1DCD Input Power Supply Power Supply FeaturesWorking Current Parameter Minimum Value Typical Value Maximum Value UnitConfiguration Working Mode Typical value Unit RemarkBand Typical Unit Configuration Value Reliability FeaturesUp/1 Down 123 Test Condition StandardTest Condition Standard ESD Test Standard Contact Discharge Air Discharge ESD FeaturesEN61000-4-2 ±4 kV ±8 kV Dimensions Mechanical SpecificationsDimensions L x W x H 35 mm x 32.5 mm x 3.05 mm 1Dimensions of the MG323 module unit mm Dimensions of the B2B ConnectorModel Stacking HRS Number Height mm 5Structure fixing hole MG323 Module Installation Description6MG323 module installation 7Machine screw dimensions Specification Selection for Fasteners8Nut dimensions 1Circuits of typical interfaces in the MG323 module Appendix a Circuits of Typical InterfacesAcronym or Abbreviation Expansion Appendix B Acronyms and AbbreviationsPCB PbcchPDU RTC
Related manuals
Manual 239 pages 48.54 Kb