EnGenius Technologies EP-490 Receiving an Intercom Call, Ending a Call, Placing a Call On Hold

Page 17

1.The LCD displays the line number of the call.

2.You can press SILENT (Left) soft key if you choose to ignore the call. Unlike turning off the ringer (from the handset menu), the SILENT key operation is valid only for the current call.

3.If Caller ID service is available, the LCD will display the incoming call information. If the LCD shows “Private” or “Unknown”, the caller’s information may have been blocked by the caller or the originating phone company.

Receiving an Intercom Call

1.When an intercom call arrives, the ringer will ring or vibrate unless the ringer has been turned off.

2.If the handset is on the charger cradle (ringer will be temporarily switched to “Ring” if it has been set to “Vibrate”), lift the handset and start conversation.

3.If the handset is not on the cradle, press any key (except PWR, END, and the SILENT soft key) to answer.

Notes:

1.The LCD displays the caller’s Handset ID.

2.You can press the SILENT (Left) soft key if you choose to ignore the call. Unlike turning off the ringer (from the handset menu), the SILENT key operation is valid only for the current call.

Ending a Call

To end a telephone or intercom call, press END key or place handset into charger cradle.

33

Adjusting Receiver (Earpiece) Voice Volume

1.Voice volume can only be adjusted during a call.

2.There are 6 levels of volume selections. Default = 4.

3.Use Up and Down Arrow key to turn up or down the earpiece volume.

4.The new setting remains effective for all future calls until changed.

Notes: To achieve maximum volume, adjust the position of the earpiece to align with the ear.

Placing a Call On Hold

1.When a call is in progress, it can be put on hold by pressing the Hold (Right) soft key.

2.To return to the conversation, press “Unhold” (Left) soft key.

Notes:

1.The call being placed on hold can only be “un-hold” by the handset that puts it on hold.

2.Handset LCD displays a call is being on hold. An alert tone (double beep) every 30 seconds will remind the handset that a call is being on hold.

3.If the operation (e.g., call transfer) after putting a call on-hold fails, the held call may be dropped.

4.You can power off the handset (e.g., change battery) while call is on hold. After power on again, you can continue the call by pressing UNHOLD (Left) soft key or select “3” from the Option menu to terminate the hold state.

34

Image 17
Contents EP-490 Table of ContentsGeneral Safety Instructions Safety InstructionsProduct Safety Instructions Battery Safety Instructions FCC ID NNA-EP-490 Regulatory InformationCongratulations Equipment ChecklistLine Indicator Basic Handset FeaturesVi Battery Strength Handset IllustrationTALK/FLASH Additional Handset FeaturesPage Line Selection Antenna Base Illustration Base FeaturesAdministrator Features Ii Auto-Attendant AA configuration On/Off, default = OffAdditional Base Station Features Charger Illustration Getting Started Charger FeaturesBase Station Installation Handset and Charger Installation Making a Telephone Call Basic OperationsMaking an Intercom Call RedialReceiving an Intercom Call Adjusting Receiver Earpiece Voice VolumeEnding a Call Placing a Call On HoldMute Battery Recharge and ReplacementDo Not Disturb Silent Ring Key GuardAdvanced Operations Handset Group Subscription Obtain a Specific Handset IDWay Conferencing Call TransferWay Conferencing with a Second Handset Way Conferencing with a Second Phone LineAuto-Attendant AA Call ForwardingPage Change AA Parameters AA Configuration by AdministratorTo add a new entry Change System Settings by AdministratorPhonebook Operations To erase/edit phonebook To search for a recordMenu Operations Text Messaging Sending a text message Viewing and editing outgoing text messagesReceiving a text message Viewing received text messagesMSK Technical Specifications