Weslo WLTL46080 user manual Refer to . Tighten all parts assembled in step

Page 12

17.Insert the left end of the Bench Pivot Rod (8) into the indicated hole in the Lat Tower (34). Loosely thread a Bench Pivot Bolt (41) with a 5/16” Washer (102) into the end of the Bench Pivot Rod.

Next, insert the right end of the Bench Pivot Rod (8) into the Upright (70) and slide the Corner Base (33) against the lower end of the Upright. Loosely thread a Bench Pivot Bolt (41) with a 5/16” Washer (102) into the end of the Bench Pivot Rod.

Loosely attach the Corner Base (33) to the Upright

(70)with two 3/8” x 3 1/4” Bolts (32), two 3/8” Washers (31), and two 3/8” Jam Nuts (11).

18.Raise the Bench Frame (5) to the position shown and hold it in place. Insert the Support Rod (25) through the indicated holes in the Lat Tower (34), the Bench Frame (5), and the Upright (70). Rotate the Support Rod to the locked position, with the hook clipped onto the Lat Tower as shown in the inset drawing.

Refer to step 17. Tighten all parts assembled in step 17.

19.Make sure that there are Handgrips (35) on the ends of the Lat Bar (36).

Attach the Lat Bar (36) to the Lat Cable (40) with a Cable Clip (37).

17

 

 

34

 

70

 

 

41

 

102

 

41

 

 

102

 

31

 

 

 

11

32

 

 

31

 

 

33

8

 

 

18

 

 

25

34

 

 

70

 

 

 

 

5

Hook

 

 

19

 

 

 

40

 

35

 

 

 

 

37

36

 

35

 

 

20.Make sure that all parts are properly tightened before you use the CADENCE DL35. If desired, attach the included allen wrench to the treadmill frame with the plastic adhesive clip.

12

Image 12
Contents Model No. WLTL46080 Serial No Customer HOT LineTable of Contents Important Precautions One decal on each side Before You Begin Part Identification Chart Assembly Page Make sure that the Cable Trap 47 is turned to Position shown, and that the PulleyTurns freely Nut. The Leg Lever must pivot freely Fully tighten all four 1/4 x 3/4 Screws 3 used in steps 12Page Refer to . Tighten all parts assembled in step How to Operate the Treadmill HOW to Plug in the Power CordPerformant Lubetm Walking Belt HOW to Lower the Treadmill for USE HOW to Fold the Treadmill for StorageDiagram of the Console Insert the key fully into the power switchResetbelt. the speed control and start the walking Step by Step Console OperationPress the Mode button to select the desired Monitor mode When you are finished, stop the walking belt Remove the keyHOW to Change the Incline of the Treadmill Measure your pulse, if desiredHow to Exercise on the Treadmill Exercise IntensityWorkout Guidelines How to Operate the Weight Bench HOW to Lower the Bench for USESuggested Stretches HOW to Adjust the Backrest Attaching Weights to the Weight CarriageLOCKING/UNLOCKING the Weight Carriage Attaching Weights to the LEG LeverHow to Exercise on the Weight Bench Strength Training GuidelinesExercise Form Staying MotivatedTrouble-Shooting and Maintenance Problem The power turns off during useTop View Problem The weight carriage sticks when the lat bar is used Part List-Model No. WLTL46080 R0898EKey Qty Description How to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT 102 142 141 1314 144 Exploded