Weslo WLTL46080 Diagram of the Console, Step by Step Console Operation, Press the ON/OFF button

Page 15

DIAGRAM OF THE CONSOLE

Speed Control

Monitor Display

Note: If there is a thin sheet of clear

 

plastic on the console, remove it.

Key

Pulse Display

Clip

Pulse Sensor

CAUTION: Before operating the con- sole, read the following important precautions.

Do not stand on the walking belt when turning on the power.

Always wear the clip while operating the tread- mill. When the key is removed from the con- sole, the power will shut off.

After the speed control is moved, there will be a pause before the walking belt begins to move.

Adjust the speed in small increments until you are familiar with the treadmill.

The training zones marked above the speed control are guidelines only. Read How to Exercise on the Treadmill on page 17 to deter- mine the proper exercise level.

To reduce the risk of electric shock, keep the console dry. Avoid spilling liquid on the con- sole and use only a sealed water bottle.

STEP BY STEP CONSOLE OPERATION

Make sure that batteries are installed in the console. (See assembly step 1 on page 7.) Next, make sure that the power cord is properly plugged in. (See How to Plug in the Power Cord on page 13). Step onto the foot rails of the treadmill. Find the clip attached to the key (see the drawing above), and slide the clip onto your waistband. Follow the steps on pages 15 and 16 to operate the console.

1 Insert the key fully into the power switch.

Note: The two dis- plays will not ap-

pear when the key is first inserted.

Key

2 Press the ON/OFF button.

The two displays will appear. Note: If batteries were just installed, the dis- plays will already appear.

3 Resetbelt. the speed control and start the walking

Slide the speed control all of the

way to the left, to the "SPEED RESET" position.

Next, slide the con- trol to the right until

the walking belt begins to move at slow speed. Carefully step onto the walking belt and begin walking. Change the speed of the walking belt as desired by sliding the speed control. Note: To stop the walking belt, slide the speed control to the "SPEED RESET" position.

15

Image 15
Contents Customer HOT Line Model No. WLTL46080 Serial NoTable of Contents Important Precautions One decal on each side Before You Begin Part Identification Chart Assembly Page Make sure that the Cable Trap 47 is turned to Position shown, and that the PulleyTurns freely Fully tighten all four 1/4 x 3/4 Screws 3 used in steps 12 Nut. The Leg Lever must pivot freelyPage Refer to . Tighten all parts assembled in step How to Operate the Treadmill HOW to Plug in the Power CordPerformant Lubetm Walking Belt HOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEStep by Step Console Operation Diagram of the ConsoleInsert the key fully into the power switch Resetbelt. the speed control and start the walkingMeasure your pulse, if desired Press the Mode button to select the desired Monitor modeWhen you are finished, stop the walking belt Remove the key HOW to Change the Incline of the TreadmillHow to Exercise on the Treadmill Exercise IntensityWorkout Guidelines How to Operate the Weight Bench HOW to Lower the Bench for USESuggested Stretches Attaching Weights to the LEG Lever HOW to Adjust the BackrestAttaching Weights to the Weight Carriage LOCKING/UNLOCKING the Weight CarriageStaying Motivated How to Exercise on the Weight BenchStrength Training Guidelines Exercise FormTrouble-Shooting and Maintenance Problem The power turns off during useTop View Problem The weight carriage sticks when the lat bar is used Part List-Model No. WLTL46080 R0898EKey Qty Description How to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT 102 142 141 1314 144 Exploded