Weslo WMTL19408 user manual Problem Solution, Walking belt slows when walked on

Page 14

PROBLEM:

SOLUTION:

PROBLEM:

SOLUTION:

The walking belt slows when walked on

 

 

a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.

b. If the walking belt is overtightened, treadmill perfor-

b

 

mance may decrease and the walking belt may be-

2"–3"

come damaged. Remove the key and UNPLUG THE

 

POWER CORD. Using the hex key, turn both rear

 

 

roller bolts counterclockwise, 1/4 of a turn. When the

 

 

walking belt is properly tightened, you should be able

 

 

to lift each edge of the walking belt 2 to 3 inches off

 

 

the walking platform. Be careful to keep the walking

 

 

belt centered. Then, plug in the power cord, insert the

 

Rear Roller

key, and run the treadmill for a few minutes. Repeat

 

until the walking belt is properly tightened.

 

Bolts

c. If the walking belt still slows when walked on, please see the front cover of this manual.

The walking belt is off-center or slips when walked on

 

 

a. If the walking belt has shifted to the left, first re-

a

 

move the key and UNPLUG THE POWER CORD.

 

Using the hex key, turn the left rear roller bolt clock-

 

 

wise 1/2 of a turn. Be careful not to overtighten the

 

 

walking belt. If the walking belt has shifted to the

 

 

right, turn the left rear roller bolt counterclockwise 1/2

 

 

of a turn. Then, plug in the power cord, insert the key,

 

 

and run the treadmill for a few minutes. Repeat until

 

 

the walking belt is centered.

 

 

b. If the walking belt slips when walked on, first remove

b

 

the key and UNPLUG THE POWER CORD. Using

 

the hex key, turn both rear roller bolts clockwise, 1/4

 

 

of a turn. When the walking belt is correctly tightened,

 

 

you should be able to lift each edge of the walking

 

 

belt 2 to 3 inches off the walking platform. Be careful

 

 

to keep the walking belt centered. Then, plug in the

 

 

power cord, insert the key, and carefully walk on the

 

 

treadmill for a few minutes. Repeat until the walking

 

 

belt is properly tightened.

 

 

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model No. WMTL19408 Serial No Version No Contact the Store Where YOU Purchased this PROD- UCTQUESTIONS? Table of Contents Treadmill until it is properly assembled. See Important PrecautionsAssembly on page 6 and HOW to Fold Page HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Move the Treadmill Pin is resting securely against the catchAssembly Wheels should turn freely Repeat this step on the left side of the treadmillPlastic Diagram of the Console Insert the key fully into the consolePRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Height and that both incline pins are fully inserted When you are finished exercising, removeFrom the console and unplug the power cord. Next Monitor your progress with the displayBefore YOU Begin For your benefit, read this manual carefully beforeMaintenance and Troubleshooting Problem The power turns off during useKey and Unplug the Power CORD. Using Problem SolutionWalking belt slows when walked on Walking belt. If the walking belt has shifted toWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart Identification Chart Description R0908AQty Qty DescriptionExploded Drawing Ordering Replacement Parts
Top Page Image Contents