Weslo WLTL19323 user manual Maintenance and Troubleshooting, Power Cord

Page 12

MAINTENANCE AND TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console (see page 9). Most problems are the result of drained batteries.

b. Remove the key from the console and

UNPLUG THE

POWER CORD.

Remove the screws from the hood.

Carefully remove the hood. Locate the Reed Switch

 

(46)and the Magnet (49) on the left side of the Pulley

(53).Turn the Pulley until the Magnet is aligned with

the Reed Switch. Make sure that the gap between

the Magnet and the Reed Switch is about 1/8”.

If

necessary, loosen the Screw (26) and move the Reed

 

Switch slightly. Retighten the Screw. Re-attach the

 

hood, and run the treadmill for a few minutes to check

 

for a correct speed reading.

 

b

1/8”

26

46

Top View

53

49

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents To Avoid DELAYS, Please Call Direct to OUR Toll QUESTIONS?Customer HOT Line Table of Contents Important PrecautionsTreadmill is capable of high speeds Treadmill on page 11. You must beDecals shown have been placed on Before YOU Begin For your benefit, read this manual carefully beforeLeft Side Assembly Assembly requires two personsDo not Until is completedWire Harness BracketVertical position With two Handrail Bolts 12 and two WashersHold the Console 1 near the Console Plate Handrail 16 to discharge any staticYou attach the Console 1 to the Console Plate Plate 4 and the ConsoleHOW to Plug in the Power Cord Performant LubeThis product must be grounded.If it should malfunc Diagram of the Console Adjust the speed in small incrementsStep -BY -STEP Console Operation TabHOW to Change the Incline of the Treadmill HOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE Maintenance and Troubleshooting Power CordProblem The walking belt slows when walked on SolutionCome damaged. Remove the key Belt has shifted to the leftHOW to Measure Your Heart Rate Conditioning GuidelinesExercise Intensity Workout GuidelinesExercise Frequency Suggested StretchesPart Identification Chart Description Circuit BreakerR0703A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R0703A
Top Page Image Contents