Weslo WLTL19323 Problem The walking belt slows when walked on, Come damaged. Remove the key

Page 13

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be-

 

come damaged. Remove the key and

UNPLUG THE

POWER CORD

. Using the allen wrench, turn both

rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walk- ing belt centered. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2”–3”

 

 

Rear Roller

 

Adjustment Bolts

c.If the walking belt still slows when walked on, please call our toll-free Customer Service Department.

PROBLEM: The walking belt is off-center or slips when walked on

 

SOLUTION:

a. If the walking belt is off-center, first remove the key

 

 

and UNPLUG THE POWER CORD

. If the walking

 

belt has shifted to the left,

use the allen wrench to

 

turn the left rear roller bolt clockwise 1/2 of a turn;

if

 

the walking belt has shifted to the right,

turn the

 

bolt counterclockwise 1/2 of a turn. Be careful not to

 

 

overtighten the walking belt. Plug in the power cord,

 

 

insert the key, and run the treadmill for a few minutes.

 

 

Repeat until the walking belt is centered.

 

a

b. If the walking belt slips when walked on, first remove

the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts clockwise,

1/4 of a turn. When the walking belt is correctly tight- ened, you should be able to lift each side of the walk- ing belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the

power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents QUESTIONS? To Avoid DELAYS, Please Call Direct to OUR TollCustomer HOT Line Important Precautions Table of ContentsTreadmill on page 11. You must be Treadmill is capable of high speedsDecals shown have been placed on For your benefit, read this manual carefully before Before YOU BeginLeft Side Assembly requires two persons AssemblyDo not Until is completedBracket Wire HarnessVertical position With two Handrail Bolts 12 and two WashersHandrail 16 to discharge any static Hold the Console 1 near the Console PlateYou attach the Console 1 to the Console Plate Plate 4 and the ConsolePerformant Lube HOW to Plug in the Power CordThis product must be grounded.If it should malfunc Adjust the speed in small increments Diagram of the ConsoleStep -BY -STEP Console Operation Tab HOW to Change the Incline of the Treadmill HOW to Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Lower the Treadmill for USE Power Cord Maintenance and TroubleshootingSolution Problem The walking belt slows when walked onCome damaged. Remove the key Belt has shifted to the leftConditioning Guidelines HOW to Measure Your Heart RateExercise Intensity Workout GuidelinesSuggested Stretches Exercise FrequencyPart Identification Chart Circuit Breaker DescriptionR0703A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R0703A
Top Page Image Contents