Weslo R 7.2 user manual Symptom The walking belt slows when walked on

Page 21

SYMPTOM: The walking belt slows when walked on

a.Use only a surge suppressor that meets all of the specifications described on page 13.

b.If the walking belt is overtightened, treadmill per- formance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b

2–3 in.

Idler Roller Screws

c.Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deterio- rate the walking belt and cause excessive wear. If you suspect that the walking belt needs more lubricant, see the front cover of this manual.

d.If the walking belt still slows when walked on, see the front cover of this manual.

SYMPTOM: The walking belt is off-center or slips when walked on

a.If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclock- wise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

a

b.If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walk- ing belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model No. WLTL39712.0 Serial No QUESTIONS?Call TOLL-FREE Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Page Before YOU Begin Assembly Attach the other Wheel 84 in the same way Make sure that the end of the Upright Wire See the far right drawing. Tie the wire tieDoes not fall into the Right Upright See the left inset drawing. Identify the twoPage Start all four Screws, and then firmly tighten them Nectors PROPERLY, the Console MAY Become Damaged When YOU Turn on PowerSide View View from Above Operation and Adjustment HOW to Connect the Power CordUse a Surge Suppressor Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Insert the key into the consoleChange the incline of the treadmill as desired Follow your progress with the displaysMeasure your heart rate if desired Select a preset application HOW to USE a Preset ApplicationWhen you are finished exercising, remove See onInformation Mode HOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USESymptom The power turns off during use TroubleshootingSymptom The walking belt slows when walked on Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part ListExploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents