Weslo WETL49710.0 user manual Troubleshooting, Problem The power turns off during use

Page 16

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 9). If an exten-

sion cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft.

(1.5 m).

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

c

 

frame near the power cord. If the switch protrudes

 

as shown, the switch has tripped. To reset the

 

 

switch, wait for five minutes and then press the

Tripped

Reset

switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 14 to turn off the demo mode.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Place the treadmill in the

storage position (see HOW TO FOLD THE TREADMILL on page 15).

 

 

Remove the six indicated M4.2 x 13mm Washer Head

 

 

 

Screws (5) and the six Foot Rail Flat Washers (25).

 

50

 

Next, lower the Frame (50) (see HOW TO LOWER

5

 

THE TREADMILL FOR USE on page 15).

5

25

 

25

 

5

 

5

 

 

 

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents QUESTIONS? Model No. WETL49710.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyStart all four Bolts, and then tighten each Them 19mm Screws 3. Be careful not to pinch Wires Become Damaged When YOU Turn onBolts, and then tighten each of them Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt AustraliaConsole Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Measure your heart rate if desired HOW to USE a Preset Workout Select one of the six preset workoutsInformation Mode HOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top ViewWalking belt. If the walking belt has shifted to Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. WETL49710.0 Key No. Qty DescriptionExploded Drawing A-Model No. WETL49710.0 R0610A Exploded Drawing B-Model No. WETL49710.0 R0610A Exploded Drawing C-Model No. WETL49710.0 R0610A Ordering Replacement Parts Recycling Information
Top Page Image Contents