5. With the help of a second person, carefully tip | 5 |
|
| B |
|
|
|
the treadmill onto its right side. Partially fold the |
|
|
|
|
| ||
Frame (48) so the treadmill is more stable; do | A |
|
|
|
|
|
|
not fully fold the Frame yet. |
|
|
| 85 |
|
| |
Remove and discard the two indicated bolts (A) | 2 81 |
|
|
| 48 |
| |
and the shipping bracket (B). |
|
|
|
|
| ||
Attach a Base Foot (81) to the Base (85) in the lo- |
|
|
|
|
|
| 27 |
cation shown with a Base Foot Spacer (104) and |
|
|
|
|
|
| |
an M4.2 x 25mm Tek Screw (2). Then, attach an- |
|
|
| 104 |
|
|
|
other Base Foot (81) with only a Tek Screw (2). |
|
|
|
|
|
| |
Remove the M10 Nut (33), the M10 x 50mm |
|
|
|
|
| 86 |
|
Bolt (27), and the shipping bracket (C) from the |
|
|
| 2 | 81 | C | |
Base (85). Attach a Wheel (86) with the Bolt and |
|
|
|
| |||
the Nut that you just removed. Do not over- |
|
|
|
|
| 33 |
|
tighten the Nut; the Wheel must turn freely. |
|
|
|
|
|
| |
Discard the shipping bracket. |
|
|
|
|
|
|
|
6. Press a Base Cap (82) into the Base (85). | 6 |
|
|
|
|
|
|
Hold a Bolt Spacer (79) inside the lower end of |
|
| 5 |
|
|
| 73 |
the Left Upright (73). Insert an M10 x 96mm Bolt |
|
|
|
|
| ||
(5) with an M10 Star Washer (8) into the Left |
|
| 8 |
|
|
|
|
Upright and the Bolt Spacer. Repeat this step |
|
|
|
|
|
| |
with a second Bolt Spacer (79), M10 x 96mm |
|
|
| 83 |
|
|
|
Bolt (5), and M10 Star Washer (8). | 82 | 79 |
|
|
|
| |
Orient the Left Upright (73) and the Left Upright |
|
|
|
|
| ||
Spacer (83) as shown. Hold the Left Upright |
| 79 |
|
|
|
|
|
Spacer and the Left Upright against the Base |
|
|
|
|
|
| |
(85). Partially tighten the M10 x 96mm Bolts (5); |
|
| 85 |
|
|
|
|
do not fully tighten the Bolts yet. |
|
|
|
|
|
| |
With the help of a second person, tip the tread- |
|
|
|
|
|
|
|
mill so that the Base (85) is flat on the floor. |
|
|
|
|
|
|
|
7. Set the Console (87) face down on a soft sur- | 7 |
|
| Console |
|
face to avoid scratching the Console. Identify the |
|
|
| ||
Right Handrail (90), which has a large hole in the |
| 90 | 1 | Wire |
|
location shown. Hold the Right Handrail near the |
|
| |||
Console. Attach the console ground wire to the |
|
|
| Large |
|
Right Handrail with a #8 x 1/2" Screw (22). |
| Console |
| Hole | 1 |
Next, insert the console wire into the large hole |
|
|
| ||
in the Right Handrail (90) and out of the top as |
| Ground Wire |
|
|
|
shown. Attach the Right Handrail with three |
|
|
|
|
|
M4.2 x 19mm Screws (1). Make sure that no |
|
|
|
|
|
wires are pinched. Start all three Screws be- |
|
| 22 |
|
|
fore tightening any of them; do not over- |
|
|
|
| |
tighten the Screws. |
| 87 |
|
|
|
Attach the Left Handrail (not shown) to the |
|
|
|
| |
Console (87) in the same way. Note: There are |
|
|
|
|
|
no wires on the left side of the Console. | 8 |
|
|
|
|
|
|
|
|
|