Weslo 7.9 warranty Troubleshooting, Compatible with GFCI-equipped outlets

Page 18

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

Tripped

Reset

tripped. To reset the circuit breaker, wait for five

minutes and then press the switch back in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 16 to turn off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

 

 

THE POWER CORD. Remove the three M4.2 x

 

13

19mm Washer Head Screws (13) and carefully

 

53

pivot the Motor Hood (53) off.

 

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. WLTL37309.0USERʼS Manual Serial No On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedDo not fully fold the Frame yet Upright Spacer 80. Be careful not to pinch 96mm Bolts 5 do not fully tighten Bolts yetNot fully fold the Frame yet Tighten the Nut the Wheel must turn freelyDo not fully tighten the Bolts yet Page Knob Spring Collar Pin Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired. Before using HOW to USE a Preset Workout Select the duration of the workout if desiredInformation Mode HOW to USE the Crosswalk ArmsHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. WLTL37309.0 Key No. Qty DescriptionKey No. Qty Description Exploded Drawing A-Model No. WLTL37309.0 R0809A Exploded Drawing B-Model No. WLTL37309.0 R0809A Exploded Drawing C-Model No. WLTL37309.0 R0809A Exploded Drawing D-Model No. WLTL37309.0 R0809A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents