JVC RX-554VBK manual Connecting the Power Cord, Putting Batteries in the Remote Control

Page 13

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

When the power cord is connected, the STANDBY lamp above the POWER button lights up.

Keep the power cord away from the connecting cables for the TV, VCR, and antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

Putting Batteries in the Remote Control

Before using the remote control, put the two supplied batteries in first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.

1.On the back of the remote control, press down on the battery cover and slide it out.

2.Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (–) to (–).

3.Slide the cover.

R6P (SUM-3)/AA (15F)

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P (SUM-3)/AA (15F) type dry-cell batteries.

Notes:

•A small amount of power is always consumed even in standby mode. To switch off the power completely, unplug the power cord from the AC outlet.

•If the power cord is unplugged (or a power failure occurs), preset settings will be erased in a few days.

CAUTIONS:

•Do not touch the power cord with wet hands.

•Do not pull on the power cord to unplug the receiver. When unplugging the receiver, always grasp the plug itself so as not to damage the cord.

CAUTIONS:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity indicated: (+) to (+) and

(–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents RX-554VBK To Reduce the Risk of Electric Shock Center Speaker Level Rear Speaker Level Effect Level For actual setting procedures, see pages 22 toTable of Contents Parts Identification Remote ControlFront Panel RX-554VBK Easy Set Up & OperationsTurn on the power General Getting StartedLocations Handling the receiverFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connecting the rear and center speakers Connecting the front speakersConnecting the Speakers Getting StartedConnecting Audio/Video Components Connecting the subwooferAudio component connections If your audio components have a Compu LINK-3 terminals Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordTurning the Power On and Off From the remote controlBasic Operations On the front panelAdjusting the Volume From the remote control onlyOn the front panel only Selecting the Front SpeakersTo listen with only headphones Listening with HeadphonesBasic Operations Recording a SourceAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes Basic SettingsTo cancel the Sleep Timer Selecting the Center Speaker SizeTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress Control @/ # to select a preset channel Press 10 keys to select a preset channel number#buttons work for tuner settings Selecting the FM Reception ModeReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @Selecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn the DAP mode On JVC 3D Phonic modeActivating the Surround Sounds On surround modesActivating the Surround Sounds Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRTo cancel the 3D-PHONIC mode Press Control @ / #to adjust the effect levelPress Effect to select the effect level Pavilion Using the DAP ModesHall To cancel the DAP mode Press Control @/ #to adjust the rear speaker output levelSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect 3CHLOGIC Select Normal or Wide for center mode Select Prologic or Theater Select Phantom for center modeSpeaker Arrangements for Surround Modes This casePrologic Preparing for Surround ModesTheater 3CHLOGICDelay Press Control @/ # to select the center modeWide NormalDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output Press Effect to adjust the effect levelBalance Press Test again to stop the test toneTo cancel surround mode Using Surround ModesFrom the front panel Select OFF in aboveRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Other Components To operate JVC audio components using this remote controlStarts playing Starts playbackYou can always perform the following operations on the TV Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM tuner FM tuner IHFGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM

RX-554VBK specifications

The JVC RX-554VBK is a versatile and feature-rich AV receiver that caters to the needs of modern home theater enthusiasts. With its sleek design and robust build quality, this receiver is designed to deliver exceptional audio and video performance, making it an ideal addition to any entertainment setup.

One of the standout features of the JVC RX-554VBK is its multi-channel surround sound capability. The receiver supports 5.1 channel audio, which creates an immersive soundscape that enhances movie watching and gaming experiences. With a total output power of 100 watts per channel, it’s powerful enough to fill medium to large rooms with rich, clear sound.

The RX-554VBK is equipped with several advanced audio processing technologies, including Dolby Pro Logic II and DTS. These technologies effectively decode surround sound formats, allowing users to enjoy films and music with remarkable audio fidelity. Additionally, the receiver is compatible with various audio formats, including MP3, WMA, and FLAC, ensuring versatile playback options for digital music lovers.

Connectivity is another highlight of the JVC RX-554VBK. It features multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices easily. The HDMI interface supports 4K video pass-through, enabling seamless integration with the latest Ultra HD televisions and projectors. Furthermore, the receiver includes component and composite video inputs, ensuring compatibility with a wide range of older and newer devices.

The on-screen display simplifies navigation through the receiver’s features, making it user-friendly for both novices and seasoned users. Additionally, the RX-554VBK supports a range of listening modes, allowing users to customize their audio experience according to their preferences, whether they're watching a movie, listening to music, or gaming.

For those who value ease of use, the JVC RX-554VBK comes with a remote control, allowing users to conveniently adjust settings from across the room. Its compact size makes it suitable for various settings without compromising on performance or features.

In summary, the JVC RX-554VBK is a powerful and user-friendly AV receiver that delivers impressive audio and video quality. Its extensive connectivity options, advanced audio processing technologies, and customizable settings make it an excellent choice for anyone looking to elevate their home entertainment experience. With the RX-554VBK, users can enjoy movies, music, and games in superior clarity and surround sound, making it a top contender in the home theater market.
Top Page Image Contents