JVC RX-554VBK manual Specifications, Amplifier

Page 40

Specifications

Output Power At Stereo operation 100 watts per channel, min. RMS, driven into 8 ohms, 40 Hz to 20 kHz with no more than 0.8 % total harmonic distortion.

Amplifier

Output Power

At Surround operation

 

 

Front channels

100 watts per channel, min. RMS,

 

 

driven into 8 ohms at 1 kHz, with no

 

 

more than 0.8 % total harmonic

 

 

distortion.

 

Center channel

100 watts, min. RMS, driven into 8

 

 

ohms at 1 kHz, with no more than 0.8

 

 

% total harmonic distortion.

 

Rear channel

100 watts, min. RMS, driven into 8

 

 

ohms at 1kHz, with no more than 0.8

 

 

% total harmonic distortion.

Total Harmonic Distortion (8 ohms, 1 kHz)

0.8 %* at 100 watts output

 

 

(* Measured by JVC Audio Analysis

 

 

System)

Frequency Response (8 ohms)

PHONO (MM)

20 Hz to 20 kHz (±1 dB)

 

CD, TAPE, VIDEO, VCR

20 Hz to 20 kHz (±1 dB)

Audio Input Sensitivity/Impedance (1 kHz)

PHONO

2.7 mV/47 k ohms

 

CD, TAPE, VIDEO, VCR

220 mV/47 k ohms

Audio Output Level

TAPE, VCR

220 mV

Signal-to-Noise Ratio (’66 IHF/’78 IHF)

PHONO

70 dB/78 dB

 

CD, TAPE, VIDEO, VCR

87 dB/80 dB

Loudness control (Volume Control at –40 dB)

+5 ±2 dB at 100 Hz

Video Input Sensitivity/Impedance

VCR, VIDEO

1 Vp-p/75 ohms

Video Output Level

VCR, MONITOR OUT

1 Vp-p (at 1 Vp-p input),

 

 

sync negative

Signal-to-Noise Ratio

45 dB

37

Page 39 Page 41
Image 40
Page 39 Page 41
Contents RX-554VBK To Reduce the Risk of Electric Shock For actual setting procedures, see pages 22 to Center Speaker Level Rear Speaker Level Effect LevelTable of Contents Parts Identification Remote ControlFront Panel Easy Set Up & Operations RX-554VBKTurn on the power Getting Started GeneralLocations Handling the receiverFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connecting the front speakers Connecting the rear and center speakersConnecting the Speakers Getting StartedConnecting Audio/Video Components Connecting the subwooferAudio component connections Video component connections If your audio components have a Compu LINK-3 terminalsConnecting the Power Cord Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and OffBasic Operations On the front panelFrom the remote control only Adjusting the VolumeOn the front panel only Selecting the Front SpeakersListening with Headphones To listen with only headphonesBasic Operations Recording a SourceBasic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerBasic Settings When the shut-off time comesTo cancel the Sleep Timer Selecting the Center Speaker SizeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo cancel a stored preset station To tune in a preset stationPress Control @/ # to select a preset channel Press 10 keys to select a preset channel numberSelecting the FM Reception Mode #buttons work for tuner settingsReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @Selecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelOn JVC 3D Phonic mode On the DAP modeActivating the Surround Sounds On surround modesUsing JVC 3D-PHONIC Modes Activating the Surround Sounds3DACTION 3DTHEATRTo cancel the 3D-PHONIC mode Press Control @ / #to adjust the effect levelPress Effect to select the effect level Pavilion Using the DAP ModesHall Press Control @/ #to adjust the rear speaker output level To cancel the DAP modeSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes PrologicTheater 3CHLOGICPress Control @/ # to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayPress Effect to adjust the effect level Press Test to start checking the speaker outputBalance Press Test again to stop the test toneUsing Surround Modes To cancel surround modeFrom the front panel Select OFF in aboveCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsStarts playing Starts playbackOperating Other Components You can always perform the following operations on the TVTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAM tuner FM tuner IHFGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM

RX-554VBK specifications

The JVC RX-554VBK is a versatile and feature-rich AV receiver that caters to the needs of modern home theater enthusiasts. With its sleek design and robust build quality, this receiver is designed to deliver exceptional audio and video performance, making it an ideal addition to any entertainment setup.

One of the standout features of the JVC RX-554VBK is its multi-channel surround sound capability. The receiver supports 5.1 channel audio, which creates an immersive soundscape that enhances movie watching and gaming experiences. With a total output power of 100 watts per channel, it’s powerful enough to fill medium to large rooms with rich, clear sound.

The RX-554VBK is equipped with several advanced audio processing technologies, including Dolby Pro Logic II and DTS. These technologies effectively decode surround sound formats, allowing users to enjoy films and music with remarkable audio fidelity. Additionally, the receiver is compatible with various audio formats, including MP3, WMA, and FLAC, ensuring versatile playback options for digital music lovers.

Connectivity is another highlight of the JVC RX-554VBK. It features multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices easily. The HDMI interface supports 4K video pass-through, enabling seamless integration with the latest Ultra HD televisions and projectors. Furthermore, the receiver includes component and composite video inputs, ensuring compatibility with a wide range of older and newer devices.

The on-screen display simplifies navigation through the receiver’s features, making it user-friendly for both novices and seasoned users. Additionally, the RX-554VBK supports a range of listening modes, allowing users to customize their audio experience according to their preferences, whether they're watching a movie, listening to music, or gaming.

For those who value ease of use, the JVC RX-554VBK comes with a remote control, allowing users to conveniently adjust settings from across the room. Its compact size makes it suitable for various settings without compromising on performance or features.

In summary, the JVC RX-554VBK is a powerful and user-friendly AV receiver that delivers impressive audio and video quality. Its extensive connectivity options, advanced audio processing technologies, and customizable settings make it an excellent choice for anyone looking to elevate their home entertainment experience. With the RX-554VBK, users can enjoy movies, music, and games in superior clarity and surround sound, making it a top contender in the home theater market.
Top Page Image Contents