JVC RX-554VBK manual From the front panel, Using Surround Modes, To cancel surround mode

Page 35

Using Surround Modes

Once you have adjusted the surround mode, you can use the same adjustments every

time you want to enjoy Surround Modes.

From the front panel:

1. Press SURROUND so that the Control %/ Þbuttons work for selecting the surround/DAP/3D-PHONIC modes.

The lamp above the button lights up.

2. Press Control %/ Þ to select one of the surround mode (“PRO LOGIC,” “3CH LOGIC” or “THEATER”).

Each time you press the button, the surround/DAP/3D- PHONIC modes change as follows:

SURROUND

Note:

When one of the surround modes is selected, the corresponding indicator lights up on the display.

Ex. PROLOGIC THEATER 3CHLOGIC

OFF 3DACTION* PAVILION*

*As for the 3D-PHONIC modes (see page 23) and the DAP modes (see page 25), one of the previously selected mode appears on the display.

3.Select and play a sound source which was processed with Dolby Surround and

is labeled with DOLBY SURROUND mark.

To cancel surround mode

Select “OFF” in step 2 above.

From the remote control:

1.Press SOUND CONTROL so that 10 keys work for adjusting the sound.

2.Press SURROUND until the mode you want appears on the display.

SOUND

CONTROL

SURROUND

3

The previous mode is recalled at first (with its previous settings) and is shown on the display.

The indicator for that mode also lights up on the display. Each time you press the button, the surround modes change as follows:

 

THEATER

 

3CHLOGIC

 

 

PROLOGIC

 

 

 

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

3.Select and play a sound source which was processed with Dolby Surround and

is labeled with DOLBY SURROUND mark.

To cancel surround mode

Select “OFF” in step 2 above.

32

Page 34 Page 36
Image 35
Page 34 Page 36
Contents RX-554VBK To Reduce the Risk of Electric Shock Center Speaker Level Rear Speaker Level Effect Level For actual setting procedures, see pages 22 toTable of Contents Front Panel Remote ControlParts Identification RX-554VBK Easy Set Up & OperationsTurn on the power Handling the receiver Getting StartedGeneral LocationsAM Antenna Connections Connecting the FM and AM AntennasFM Antenna Connections Getting Started Connecting the front speakersConnecting the rear and center speakers Connecting the SpeakersAudio component connections Connecting the subwooferConnecting Audio/Video Components If your audio components have a Compu LINK-3 terminals Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordOn the front panel From the remote controlTurning the Power On and Off Basic OperationsSelecting the Front Speakers From the remote control onlyAdjusting the Volume On the front panel onlyRecording a Source Listening with HeadphonesTo listen with only headphones Basic OperationsUsing the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessSelecting the Center Speaker Size Basic SettingsWhen the shut-off time comes To cancel the Sleep TimerOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Press Control @/ # to select a preset channelPress TUNER/BAND so that the Control %/ Þ/ @ Selecting the FM Reception Mode#buttons work for tuner settings Receiving Radio BroadcastsTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes On JVC 3D Phonic modeOn the DAP mode Activating the Surround Sounds3DTHEATR Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DACTIONPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Hall Using the DAP ModesPavilion Press Rear +/- to adjust the rear speaker output level Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Select OFF in step DAP indicator goes off from the displayThis case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround Modes3CHLOGIC Preparing for Surround ModesPrologic TheaterNormal Press Control @/ # to select the center modeDelay WideDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test again to stop the test tone Press Effect to adjust the effect levelPress Test to start checking the speaker output BalanceSelect OFF in above Using Surround ModesTo cancel surround mode From the front panelSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionStarts playback To operate JVC audio components using this remote controlOperating Other Components Starts playingYou can always perform the following operations on the TV Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsGeneral FM tuner IHFAM tuner HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM

RX-554VBK specifications

The JVC RX-554VBK is a versatile and feature-rich AV receiver that caters to the needs of modern home theater enthusiasts. With its sleek design and robust build quality, this receiver is designed to deliver exceptional audio and video performance, making it an ideal addition to any entertainment setup.

One of the standout features of the JVC RX-554VBK is its multi-channel surround sound capability. The receiver supports 5.1 channel audio, which creates an immersive soundscape that enhances movie watching and gaming experiences. With a total output power of 100 watts per channel, it’s powerful enough to fill medium to large rooms with rich, clear sound.

The RX-554VBK is equipped with several advanced audio processing technologies, including Dolby Pro Logic II and DTS. These technologies effectively decode surround sound formats, allowing users to enjoy films and music with remarkable audio fidelity. Additionally, the receiver is compatible with various audio formats, including MP3, WMA, and FLAC, ensuring versatile playback options for digital music lovers.

Connectivity is another highlight of the JVC RX-554VBK. It features multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices easily. The HDMI interface supports 4K video pass-through, enabling seamless integration with the latest Ultra HD televisions and projectors. Furthermore, the receiver includes component and composite video inputs, ensuring compatibility with a wide range of older and newer devices.

The on-screen display simplifies navigation through the receiver’s features, making it user-friendly for both novices and seasoned users. Additionally, the RX-554VBK supports a range of listening modes, allowing users to customize their audio experience according to their preferences, whether they're watching a movie, listening to music, or gaming.

For those who value ease of use, the JVC RX-554VBK comes with a remote control, allowing users to conveniently adjust settings from across the room. Its compact size makes it suitable for various settings without compromising on performance or features.

In summary, the JVC RX-554VBK is a powerful and user-friendly AV receiver that delivers impressive audio and video quality. Its extensive connectivity options, advanced audio processing technologies, and customizable settings make it an excellent choice for anyone looking to elevate their home entertainment experience. With the RX-554VBK, users can enjoy movies, music, and games in superior clarity and surround sound, making it a top contender in the home theater market.
Top Page Image Contents