JVC RX-554VBK FM Antenna Connections, AM Antenna Connections, Connecting the FM and AM Antennas

Page 9

Connecting the FM and AM Antennas

FM Antenna Connections

123

FM Antenna

ANTENNA

Extend the FM antenna horizontally.

 

 

 

FM

 

 

 

 

75

 

 

 

 

FM

 

 

Outside FM Antenna Cable

GND

 

 

 

 

 

 

GND

1

2

3

7/16 in.

AM

LOOP

AM

13/16 in.

EXT

(10 mm)

 

 

(20 mm)

Note:

If reception is poor, connect the outside antenna.

Before attaching a 75 Ω coaxial cable (the kind with a round wire going to an outside antenna), disconnect the supplied FM wire antenna.

How to strip the 75 Ω coaxial cable and connect it to the FM terminals

1.Strip back the outside covering of the 75 Ω coaxial cable to expose the braided metallic mesh about 13/16 inches (20 mm).

2.Pull the mesh back and twist it into a single connector as shown in the illustration above.

3.Strip the insulation about 7/16 inches (10 mm) back from the central wire.

4.Insert the twisted mesh and the central wire to the FM terminals, as shown in the illustration above.

AM Antenna Connections

ANTENNA

Turn the loop until you have

 

 

the best reception.

FM

AM

LOOP

FM 75

GND

AM Loop Antenna

GND

AM

EXT

Snap the tabs on the loop into the slots of the base to assemble the AM loop.

Notes :

• Make sure the antenna

conductors do not touch any

other terminals, connecting

cords and power cord. This

could cause poor reception.

• If reception is poor, connect an

outdoor single vinyl-covered

wire to the AM EXT terminal.

123

Outdoor Single Vinyl- covered Wire

(Keep the AM loop antenna

connected.)

6

Page 8 Page 10
Image 9
Page 8 Page 10
Contents RX-554VBK To Reduce the Risk of Electric Shock Center Speaker Level Rear Speaker Level Effect Level For actual setting procedures, see pages 22 toTable of Contents Remote Control Parts IdentificationFront Panel RX-554VBK Easy Set Up & OperationsTurn on the power General Getting StartedLocations Handling the receiverConnecting the FM and AM Antennas FM Antenna ConnectionsAM Antenna Connections Connecting the rear and center speakers Connecting the front speakersConnecting the Speakers Getting StartedConnecting the subwoofer Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminals Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordTurning the Power On and Off From the remote controlBasic Operations On the front panelAdjusting the Volume From the remote control onlyOn the front panel only Selecting the Front SpeakersTo listen with only headphones Listening with HeadphonesBasic Operations Recording a SourceAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes Basic SettingsTo cancel the Sleep Timer Selecting the Center Speaker SizeTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress Control @/ # to select a preset channel Press 10 keys to select a preset channel number#buttons work for tuner settings Selecting the FM Reception ModeReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @Using the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn the DAP mode On JVC 3D Phonic modeActivating the Surround Sounds On surround modesActivating the Surround Sounds Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRPress Control @ / #to adjust the effect level To cancel the 3D-PHONIC modePress Effect to select the effect level Using the DAP Modes PavilionHall To cancel the DAP mode Press Control @/ #to adjust the rear speaker output levelSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect 3CHLOGIC Select Normal or Wide for center mode Select Prologic or Theater Select Phantom for center modeSpeaker Arrangements for Surround Modes This casePrologic Preparing for Surround ModesTheater 3CHLOGICDelay Press Control @/ # to select the center modeWide NormalDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output Press Effect to adjust the effect levelBalance Press Test again to stop the test toneTo cancel surround mode Using Surround ModesFrom the front panel Select OFF in aboveRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Other Components To operate JVC audio components using this remote controlStarts playing Starts playbackYou can always perform the following operations on the TV Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerGeneral HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1297OFMMDWJEM

RX-554VBK specifications

The JVC RX-554VBK is a versatile and feature-rich AV receiver that caters to the needs of modern home theater enthusiasts. With its sleek design and robust build quality, this receiver is designed to deliver exceptional audio and video performance, making it an ideal addition to any entertainment setup.

One of the standout features of the JVC RX-554VBK is its multi-channel surround sound capability. The receiver supports 5.1 channel audio, which creates an immersive soundscape that enhances movie watching and gaming experiences. With a total output power of 100 watts per channel, it’s powerful enough to fill medium to large rooms with rich, clear sound.

The RX-554VBK is equipped with several advanced audio processing technologies, including Dolby Pro Logic II and DTS. These technologies effectively decode surround sound formats, allowing users to enjoy films and music with remarkable audio fidelity. Additionally, the receiver is compatible with various audio formats, including MP3, WMA, and FLAC, ensuring versatile playback options for digital music lovers.

Connectivity is another highlight of the JVC RX-554VBK. It features multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices easily. The HDMI interface supports 4K video pass-through, enabling seamless integration with the latest Ultra HD televisions and projectors. Furthermore, the receiver includes component and composite video inputs, ensuring compatibility with a wide range of older and newer devices.

The on-screen display simplifies navigation through the receiver’s features, making it user-friendly for both novices and seasoned users. Additionally, the RX-554VBK supports a range of listening modes, allowing users to customize their audio experience according to their preferences, whether they're watching a movie, listening to music, or gaming.

For those who value ease of use, the JVC RX-554VBK comes with a remote control, allowing users to conveniently adjust settings from across the room. Its compact size makes it suitable for various settings without compromising on performance or features.

In summary, the JVC RX-554VBK is a powerful and user-friendly AV receiver that delivers impressive audio and video quality. Its extensive connectivity options, advanced audio processing technologies, and customizable settings make it an excellent choice for anyone looking to elevate their home entertainment experience. With the RX-554VBK, users can enjoy movies, music, and games in superior clarity and surround sound, making it a top contender in the home theater market.
Top Page Image Contents