Reebok Fitness RBTL09906.1 manual Troubleshooting, Problem The power turns off during use

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call the toll-free telephone number on the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 11. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes, and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The display of the console does not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Next, carefully lower the Uprights

(84). Remove the two indicated 3/4” Screws (2). Note: A phillips screwdriver with a shaft at least 8” long is needed.

a

84

2

2

25

Image 25
Contents Model No. RBTL09906.1 Serial No QUESTIONS?Call TOLL-FREE Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Power Lines Service Back Right Side Before YOU BeginMake sure that the power cord is unplugged AssemblyPage Bolts and then firmly tighten them Small Cylinder Wire Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredSelect a preset program HOW to USE a Preset ProgramFollow your progress with the displays Put on the chest pulse sensor HOW to USE a Heart Rate ProgramSelect a heart rate program Follow your progress with the displays Select a custom program HOW to Create a Custom ProgramHOW to USE a Custom Program Press the Volume VOL. buttons to adjust HOW to Operate the Personal TelevisionHOW to USE the Information Mode Turn on the televisionOptional Chest Pulse Sensor Press the On/Off button again and select a Cable connectionHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top Problem Television reception is poor Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description R1207AKey No. Qty Description Exploded Drawing a Exploded Drawing B-Model No. RBTL09906.1 R1207A Exploded Drawing C-Model No. RBTL09906.1 R1207A Exploded Drawing D-Model No. RBTL09906.1 R1207A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT