Healthrider HRTL89406.2 manual Top View Problem The walking belt slows when walked on

Page 27

Locate the Reed Switch (22) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, move the Reed Switch slightly using a slotted screwdriver. Next, reat- tach the Motor Hood (not shown), making sure that the 3/4” Screws (not shown) are in the same holes from which they were removed. Then, run the treadmill for a few minutes to check for a correct speed reading.

Top

View

22

1/8”

17

18

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

3”–4”

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walk- ing belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents QUESTIONS? Model No. HRTL89406.2 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Power Lines Service Before YOU Begin Make sure that the power cord is unplugged AssemblySure that all of the holes are aligned see Again. if the Connectors are not CON75 Ohm HOW to Connect AN External Source Using a Catv Cable HOW to Connect a 75 OHM Catv CableChest Pulse Sensor Troubleshooting HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor Chest Pulse Sensor Care and MaintenanceOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerContacts for about 15 seconds Follow your progress with the displaysMeasure your heart rate if desired Pulse sensor. Next, stand on the foot railsWhenkey. you are finished exercising, remove HOW to USE a Preset ProgramSelect a preset program Turn on the fan if desiredWorkout Intensity bar Incline settings for the next segmentHOW to USE a Distance Program Select a Distance programTurn on the fans if desired HOW to Create a Custom Program Programsettings. the desired speed and inclineSelect a Custom program HOW to USE a Custom Program HOW to USE a Pulse Program Adjust the maximum target heart rate setting if DesiredSelect a Pulse program Follow your progress with the displays Workout Intensity bar Press the Channel buttons to select Desired cable channel HOW to Operate the Personal TelevisionPress the Volume buttons to adjust the volume Press the On/Off button to turn on TelevisionHOW to USE the Information Mode HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked on Problem The chest pulse sensor does not function properly Problem Television reception is poorExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R1207AOrdering Replacement Parts Exploded Exploded Drawing B-Model No. HRTL89406.2 R1207A Exploded Drawing C-Model No. HRTL89406.2 R1207A Exploded Drawing D-Model No. HRTL89406.2 R1207A Limited Warranty
Top Page Image Contents