Healthrider H90T manual Operation and Adjustment, PRE-LUBRICATED Walking Belt

Page 14

OPERATION AND ADJUSTMENT

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply sil- icone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or service- man if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your homeʼs power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right). To purchase a surge suppressor, please see your local electronics store.

Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup- pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. There must be a moni- toring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow, accelerate, or stop unexpectedly, which may result in a fall and serious injury.

This product must be grounded. If it should malfunc- tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of elec- tric shock. This product is equipped with a cord having

an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illus- trated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available.

1

Grounded Outlet Box

 

 

Surge Suppressor

 

 

Grounding Pin

 

Grounding Pin

2

Grounded Outlet

Grounding Plug

Grounded Outlet Box

 

 

Adapter

Surge Suppressor

Lug

Metal Screw

The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician.

The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified elec- trician to determine if the outlet box cover is grounded before using an adapter.

14

Image 14
Contents QUESTIONS? Model No. HMTL07508.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Montaje Completely assembled Make sure that the power cord is unpluggedNot fully fold the Frame until the treadmill is Tek Screws 4 do not overtighten the TekSee the inset drawing. Tie the wire tie Fully tighten the Patch Bolts yetPage Console assembly. See the inset drawing Repeat this step with the Right Handrail CoverUprights. Be careful not to pinch any wires Patch Bolts before tightening any of them104 Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Follow your progress with the displays. The matrix-When you Measure your heart rate if desired. Before using Turn on the fans if desiredStart the walking belt HOW to USE a Preset WorkoutSelect a preset workout HOW to Create a Custom Workout Select a custom workoutHOW to USE a Custom Workout Make sure that the audio wire is fully plugged Information ModeHOW to USE the Stereo Sound System HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Important The treadmill is not TroubleshootingProblem The power turns off during use Compatible with GFCI-equipped outletsProblem The walking belt slows when walked on TopProblem Solution Walking belt is off-center or slips when walked onWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. HMTL07508.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. HMTL07508.0 R1008A Exploded Drawing B-Model No. HMTL07508.0 R1008A Exploded Drawing C-Model No. HMTL07508.0 R1008A Exploded Drawing D-Model No. HMTL07508.0 R1008A Exploded Drawing E-Model No. HMTL07508.0 R1008A Ordering Replacement Parts