Reebok Fitness RBEL9906.1 manual Maintenance and Troubleshooting, HOW to Adjust the Belt

Page 22

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. Important: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

HOW TO LEVEL THE ELLIPTICAL EXERCISER

HOW TO ELIMINATE FLEXING IN THE CENTER OF THE ELLIPTICAL EXERCISER

If the elliptical exerciser flexes in the center during use, turn the center foot beneath the frame (see the drawing at the left) until the flexing is eliminated.

HOW TO ADJUST THE BELT

If the pedals slip

while you are

If the elliptical exerciser rocks on your floor dur- ing use, turn one or both of the leveling feet beneath the rear stabilizer until the rocking motion is elimi- nated.

Center

Foot

Leveling

Feet

pedaling, even

 

while the resis-

 

tance is adjusted

 

to the highest

 

setting, the belt

 

may need to be

 

adjusted. To

13

adjust the belt,

12

first carefully pry

 

off the left Disc

 

Cover (13) using a flat screwdriver. Next, remove the four screws (not shown) from the center of the left Disc (12). Gently rotate the Disc Cover and the Disc

HANDGRIP PULSE SENSOR TROUBLESHOOTING

Avoid moving your hands while using the handgrip pulse sensor. Excessive movement may interfere with heart rate readings.

Do not hold the metal contacts too tightly; doing so may interfere with heart rate readings.

For the most accurate heart rate reading, hold the metal contacts for about 30 seconds.

For optimal performance of the handgrip pulse sen- sor, keep the metal contacts clean. The contacts can be cleaned with a soft cloth—never use alco- hol, abrasives, or chemicals to clean the con- tacts.

away from the elliptical exerciser.

Loosen, but do

 

not remove, the

 

three 1/4" x

 

19mm Button

 

Screws (114).

 

Insert the shaft of

47

a screwdriver

48

downward

114 96

between the

Idler (47) and the

 

Idler Pulley (48).

 

Pull the top of the

 

screwdriver

toward the rear of the elliptical exerciser until the Belt (96) is tight, and then tighten the three Button Screws.

Reattach the left disc with the four screws and then reattach the left disc cover.

22

Image 22
Contents Mon.-Fri., 6 a.m.-6 p.m. MST Model No. RBEL9906.1 Serial NoCall TOLL-FREE On the WEBTable of Contents Important Precautions Right Side Before YOU BeginFront RearAssembly Screw M10 x 93mm Button ScrewGrease See the inset drawing. Lift the Pedal Arm 107 Repeat this step with the Right Link Arm Attach the Right Link Arm 31 in the same way HOW to Plug in the Power Cord HOW to USE the Elliptical ExerciserHOW to Fold and Unfold the Elliptical Exerciser HOW to Move the Elliptical Exerciser HOW to Exercise on the Elliptical ExerciserConsole Diagram Features of the ConsolePedaling to turn on the console HOW to USE the Manual ModeSelect the manual mode Pedals and the incline of the ramp as desiredTurn on the fan if desired Will turn off automaticallyTurn on the console. See on Select a preset program HOW to USE a Preset ProgramBegin pedaling to start the program Follow your progress with the display HOW to Create a Custom ProgramProgram the desired settings Turn on the console. See on Select a custom programUsing it. To change the resistance level for HOW to USE a Custom ProgramMemory. To change the target pace for the cur Enter a target heart rate setting HOW to USE a Heart Rate ProgramTurn on the console. See on Select a heart rate program Begin pedaling to start the program HOW to USE AN Ifit Program HOW to USE the Stereo Sound SystemHOW to Adjust the Belt Maintenance and TroubleshootingHandgrip Pulse Sensor Troubleshooting Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyPart LIST-MODELNO. RBEL9906.1 Key No. Qty DescriptionQty Description Exploded Drawing A-MODEL NO. RBEL9906.1 R1206A Exploded Drawing B-MODEL NO. RBEL9906.1 Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT